Dala's Likes Received

Easy,

Closed loop, uncheck the "Enable Closed Loop" tickbox
http://www.nismotronic.com/Help/images/ENABLE_CLOSED_LOOP.JPG

Then, go to Setup -> Extras ->DTC Mask
Uncheck 02 sensor to avoid g...

You say you're running no 02 sensor, but you are running a wideband right?

Why not connect the wideband to NEMU? That way you can run Wideband02 closed loop, and achieve great idle AFR.

I feel like every post I've made here lately is about the TPS :)

Readings on ground pin:
0 Ohm resistance to ground

Readings on signal pin:
Throttle fully closed 0.45-0.55V
Throttle partia...

I feel like every post I've made here lately is about the TPS :)

Readings on ground pin:
0 Ohm resistance to ground

Readings on signal pin:
Throttle fully closed 0.45-0.55V
Throttle partia...

Take a multimeter and measure the ground resistance on your TPS connector (its the black pin). Should be as close to 0 as possible.

You need a extra breakout board to handle the 0-5V step-up conversion, for example, a quick ebay search on "Thermocouple to voltage converter" will get you what you need. Should be about 20$ with f...

This .tcd is from the above mentioned folder, should be perfect as a starting point

"SR20VE (330 B13).tcd"
[ATTACH]824[/ATTACH]

-SR20VE
-330cc inj
-B13 maf

Hello Monder, what an excellent choice you've made to go with the Nismotronic Speed Density solution.


All factory SR20 engines come equipped with a knock sensor. If you are unsure about detect...

Here's what I configured in NEMU after permanent install:
http://i.imgur.com/8be8T0f.png
Right, so I'm adding 40% fuel at maximum voltage (E85). At the middle spectrum, 20% fuel is added. This is...

Here's what I configured in NEMU after permanent install:
http://i.imgur.com/8be8T0f.png
Right, so I'm adding 40% fuel at maximum voltage (E85). At the middle spectrum, 20% fuel is added. This is...

Here's what I configured in NEMU after permanent install:
http://i.imgur.com/8be8T0f.png
Right, so I'm adding 40% fuel at maximum voltage (E85). At the middle spectrum, 20% fuel is added. This is...

Plumbed the idle hose to the charge pipe pre-tb. Not much difference really, but it will help me sleep at night :) (maxed out my injectors at 9psi whilst tuning :D)

D-unit has been helping me alot with the initial testing, kudos to him :)

On todays agenda, we need to get the RC-filter sorted out. D-Unit121 , I need some more values from you!

http://i.imgur....

Tested it on my car today, doublechecked the calibration with a multimeter, was within 0.7Hz accurate! Seems good enough to me! :D

http://i.imgur.com/Wsky9iK.png

Awesome!

I picked up a trashed android phone and flashed it to Lollipop (5.0.2), gonna see if a lowram unit can run this application, else I will switch to a dedicated tablet
http://i.imgur.com...

A picture explains this quite clearly:
http://i.imgur.com/kSdlBaS.jpg

I almost did the same thing when I installed my MAP sensor :P

A picture explains this quite clearly:
http://i.imgur.com/kSdlBaS.jpg

I almost did the same thing when I installed my MAP sensor :P

Had a breakthrough in development and got the sensor to co-operate nicely with the microcontroller. Threw it into the glovebox for now.
http://i.imgur.com/uUcgKiD.jpg

It seems to be pretty spo...

Awesome!

I picked up a trashed android phone and flashed it to Lollipop (5.0.2), gonna see if a lowram unit can run this application, else I will switch to a dedicated tablet
http://i.imgur.com...

Awesome!

I picked up a trashed android phone and flashed it to Lollipop (5.0.2), gonna see if a lowram unit can run this application, else I will switch to a dedicated tablet
http://i.imgur.com...

Awesome!

I picked up a trashed android phone and flashed it to Lollipop (5.0.2), gonna see if a lowram unit can run this application, else I will switch to a dedicated tablet
http://i.imgur.com...

Awesome!

I picked up a trashed android phone and flashed it to Lollipop (5.0.2), gonna see if a lowram unit can run this application, else I will switch to a dedicated tablet
http://i.imgur.com...

The code will be stored if it triggered the light.

I had the same issue over a year ago, turned out to be a MAP code altough I didn't have a MAP sensor at the time.

Find the code, and disable...

This piece of engineering arrived yesterday:
http://i.imgur.com/3qhcX4z.jpg

Time to start programming. I simulated a PWM output, and sampled it back into the microprocessor. You NEED an oscillosco...

This piece of engineering arrived yesterday:
http://i.imgur.com/3qhcX4z.jpg

Time to start programming. I simulated a PWM output, and sampled it back into the microprocessor. You NEED an oscillosco...