Dala's Likes Received

This piece of engineering arrived yesterday:
http://i.imgur.com/3qhcX4z.jpg

Time to start programming. I simulated a PWM output, and sampled it back into the microprocessor. You NEED an oscillosco...

There are great solutions ready to be purchased, but they all cost a significant amount of money. Let's crack out the microprocessor!

Fiddling with my old ATMega644p, this is how it looked last ...

There are great solutions ready to be purchased, but they all cost a significant amount of money. Let's crack out the microprocessor!

Fiddling with my old ATMega644p, this is how it looked last ...

I am currently programming, watch this space in 3 hours.

+1 on what he said^^

If you are suspecting that your solenoids are stuck on, unplug them and probe the terminals with a multimeter. One pin should be constant +12V, and the other should be a switc...

Time to bump this thread with new info.

If you install aftermarket block heater, they don't mount to the rear of the engine. They go on the front. There are pros & cons to both types, installing...

http://static1.wikia.nocookie.net/__cb20131209013558/theamazingworldofgumball/images/0/0e/Wat_zps3c5b202d.jpg
Is Nismotronic considered a reflashed ECU nowadays? :P

Back on topic:
If you are unsur...

Time to bump this thread with new info.

If you install aftermarket block heater, they don't mount to the rear of the engine. They go on the front. There are pros & cons to both types, installing...

Walbro 255 is def the pump to get if you want it cheap and simple

Handles my < 300hp VE-T with E85 just fine.. 2½ years since install now, and sounds just like the day i bought it :)

Since your setup is a very basic one, I'd say that starting from the base tunes alone would be just fine. If you stress too much about it, get the e-tune.

Hell, I started a SR20VE-T, 10.3:1 comp...

If everything seems normal, no need to tear it down.

Heck, SR20's are tougher than most think, I've hydrolocked mine with fuel (don't ask me how), and overheated the coil by cranking it with no pl...

4:th attempt

Result: Pass :D

http://i.imgur.com/yt5Wo8r.jpg
These were the readings. Nismotronic settings, "Enable Closed Loop" [X], "NB02 Closed Loop" [X].

I deviated from the first post...

+1 on the OR function! I'm wiring in an intercooler sprayer, and would like to make it go on if IAT > x degrees OR load > x mbar

Would it be able to assign names to the Generic Outputs?
Like th...

Nice build, but did you really connect the crankcase ventilation to the charge pipe?
http://i.imgur.com/hM0krAA.jpg
That my friend is a big mistake. You are putting the crankcase under some serio...

Most people I know never change their brake fluid! And then they wonder why brake lines rot...

The trick is not what brake fluid to use, but how often to change it. 3x per decade should be what ...

Agreed with steve, curlz's nx looks so tasty! :bigthumbup:

Winter is coming, and my clutch is starting to slip under pressure...
http://i.imgur.com/PRKib7Y.jpg

I'm installing the boost PWM solenoid to Nismotronic tonight!

My understanding, is that Nismotronic doesn't know what your gate pressure is (only manifold pressure if you run MAP). You have to m...

Okay, so this is how it went down today. Set out to the garage for a full evening of troublehooting.

Disconnected distributor, removed fuel pump fuse.

Set the key to ON, turned the distributo...

Nice build, but did you really connect the crankcase ventilation to the charge pipe?
http://i.imgur.com/hM0krAA.jpg
That my friend is a big mistake. You are putting the crankcase under some serio...

Nice build, but did you really connect the crankcase ventilation to the charge pipe?
http://i.imgur.com/hM0krAA.jpg
That my friend is a big mistake. You are putting the crankcase under some serio...

Nice build, but did you really connect the crankcase ventilation to the charge pipe?
http://i.imgur.com/hM0krAA.jpg
That my friend is a big mistake. You are putting the crankcase under some serio...

http://i110.photobucket.com/albums/n104/DaMasterPNut/SR20VE/SR1620VEECUpinoutdiagram.jpg

If this is correct, take pin 102 & 106 on the VE harness, and connect it to pin 11 on the ECU

http://i110.photobucket.com/albums/n104/DaMasterPNut/SR20VE/SR1620VEECUpinoutdiagram.jpg

If this is correct, take pin 102 & 106 on the VE harness, and connect it to pin 11 on the ECU

DIY Intercooler Water Sprayer

+1 on the OR function! I'm wiring in an intercooler sprayer, and would like to make it go on if IAT > x degrees OR load > x mbar

Would it be able to assign names to the Generic Outputs?
Like th...