All posts liked by sss4me
Ok, so I guessing this is the final product then and your car was not the test car. Test car had 2.25" with nismotronic and you have 2.5" with nistune.
The after gains are just header or is tha...
Got one of Trackforged fine header on my sr20ve the other day. Here's a few pics. We saw about +3-5hp and +6-10ftlb over a ported SSAC. Set up at time 2.5 exhaust,intake,n1 cams, s&r and nistune fo...
yes, scale the maps so your trace does not go all the way to max load. you want to have your map a few values higher then its max, but not too far because you still want your last column to be used.
https://scontent-a-lax.xx.fbcdn.net/hphotos-ash3/t31/1658230_10152212601593491_719423361_o.jpg
https://scontent-a-lax.xx.fbcdn.net/hphotos-prn2/t31/1836611_10152212601658491_141380926_o.jpg
Snickers advised me to run the p12 20v cams. I had n1's like you on my n/a motor. Those cams were pulled and sold when I boosted the motor. As miko stated sr16ve cams or p12 20v.
Will be posting soon for both lowport and VE!!!
When the quaife gb was run the initial diff's ended up needing additional machining for them to fit, so having someone in the US willing to test is a priority IMO. The initial test fit by one of o...
This header will perform better than SSAC since merge collectors flow better and it has the 2in secondaries that its the mod many people do to the SSAC with good results with the 2.25ID Choke a tra...
EGR? Who still has that outside of california?
No we are not using a burns collector, to use them the prices would skyrocket
Right now we do not have a current price on this header, we need to go through our testing process first and deem the header worthy of the price. Also we may also end up revising this header if we ...
What dimensions you want of my header??
My header have 1.75, 1.88 and 2.0 in OD primaries
Choke 2.25 ID
Megaphone on that pic is 2.25>4>2.5 about 16in long
The other Megaphone goes from 1.5 to...
I am pretty sure its 2.25 since the last merge collector has a 2.5 tube welded over it but if you look on the inside the choke its smaller then the pipe
Sent from my SM-N900P using Tapatalk
The pinions between the 32A and 32V are the same, so it's only the ring gear that we need to make. Hopefully should have them ready in 4-6 weeks time :)
when I made the first triy it was 2" the choke but then switch to 2.25 gain better and 2.5 was to.much even for my 2.1lt and for a 90mm had
Sent from my SPH-L900 using Tapatalk
3" collector is very bad idea... stick to the Payu´s 2.25" idea.
Make the choke 2.25 it will work better
Sent from my SM-N900P using Tapatalk
In my opinion a as equal as possible Tri stepped tri-y header with 1.75in, 1.88in and 2.0in primaries and 23-25in primaries with 2.25 secondaries and 2.25 choke will fit 80% of the DE and VE owner...
At least on my 13:1 88mm motor I could not use Standard 5 Heat range plug since the tip of the plug touched the dome of the piston!! 6 or 7 are fine for ALL MOTOR 12.5-13:1 motor!!
http://i43.tinypic.com/sxgjcw.jpg
Awaiting the "GL-5" users....
http://i.imgur.com/W4bTe.gif
those are my runners I ported them and yes thier like plastic and I glue them because they where coming off but problem fix
Re: Timing chain tensioner going bad? (I have the old style one wth?)