All posts liked by sss4me
Excellent news...........also will the new breakout box have more than four adc's.....
i guess congrats are in order +++++Wedding++++
I feel like every post I've made here lately is about the TPS :)
Readings on ground pin:
0 Ohm resistance to ground
Readings on signal pin:
Throttle fully closed 0.45-0.55V
Throttle partia...
i sat with dave blundell the guy who actually made nismotronics, and we tried to figure this out, we did a little street tuning not at fast speeds but at normal driving speeds, he was logging every...
Your open/close and close/open deltas are not set right. They are way too close to be working right I would suspect. You offset initial should be as close to closed throttle voltage as possible. Yo...
Take a multimeter and measure the ground resistance on your TPS connector (its the black pin). Should be as close to 0 as possible.
Nismotronic lets you customize your load and RPM scales on the tables so you can tune for a much higher RPM range than stock, and larger tables, 20x20 rather than 16x16. Nismotronic has inputs for ...
Make sure you update your Nismotronic software. Then download the new Startup Calibrations folder from here: NismoTronicSA DEMO Download
Pick one of them and the MAF and everything is correct. W...
Well it´s up and running and it´s fucking beautifull... love it...
Proof:
[url= URL=http://s173.photobucket.com/user/nunomrpinto/media/N14%20GTi/11038475_10206585593703200_7387654248177080...
What part of SF? You can always get nismotronic, and get an e-tune from them. Schedule a time on the dyno and coordinate with jk tuning so they can remote in.
If you need something quick and dir...
Not if you are using the SR16VE crank.
Iam sporting the Apex WS2 with 3" piping and a 14" resonator. Its quiet at idle and great when VVL hits.
https://www.youtube.com/watch?v=BsOEpcaaKpQ
I still can barely believe Nissan is wringing money out of this chassis. Make a new one that is lighter, and 4 cyl turbo powered and watch them sell some units.
Pulled the VET solenoid off. It is the same as the P12 NA solenoid. When I put pressure on the feed and hook power to the solenoid it opens both IN and EX cam holes. Also note that my IN and EX mar...
Installing MFactory helical differential in a RS5F32V
Hey Guys,
just to say that we are not just sitting here idly, and have been trying to work out what the issue is here.
originally, the issue with the test samples were clear and we have removed e...
I will try to get something soon.All I have now is on the dyno in an echochamber...lol
I think it is to early to borrow trouble and worry about rebuilding the tranny. Check for other causes first. Shift rods, bushings, etc..
I had first gear pop-out in my B13 tranny even thought the...
You may be 100% correct in all of your other statements, but your hyperbole as bolded is actually weakening and undermining your argument.
Not a single person I have ever read comment on our stock...
If this is developed, it will be our 2nd Gen design:
- Fully adjustable pre-load via 12 positive coil springs
- Completely redesigned friction plates to minimise chatter, whilst increasing resp...
5.1FD is great for a street or circuit car, as long as you dont do many highway miles. 70mph Will be like 4000rpm. 1st gear will be very short, making it perhaps not so good for drag racing.
I ...
Ok guys, LSD's are under final processing just now and should be ready to ship out next week!
Please accept my sincerest sincerest apologies for the long delay on these.
Everyone that has put...
No the 20v plenum and p11 plenum have different bolt pattern
Complete kit --- $69.00 SHIPPED! Includes the following:
Front Cover
Rear Main
Water Pump
Inner Baffle
Girdle Baffle
Oil Pan Baffle
Oil Filter Housing
Oil Strainer
Upper Oi...