All posts made by Boostlee that members have liked.
On it!
I pmed him about the MAP sensor and awaiting a response :)
I may also be able to dig up some intercooler piping, Just need to know the lenghts and specs on what he needs!
I also have a EG...
Well good for you then......And glad it's working for your needs. I am no-one you should be impressing or care if you impress me FWIW. Fact of the matter it [color= COLOR=#FF0000][/color]IS a knock...
I want to bring this back from the dead :D
So I went for emissions yesterday and took my laptop with me to do live A/F correction. The tester had zero issues with my adjustments during the test ...
I want to bring this back from the dead :D
So I went for emissions yesterday and took my laptop with me to do live A/F correction. The tester had zero issues with my adjustments during the test ...
You can run either MAF or MAP with a MAC boost control solenoid controlled via Nismotronic.
I want to bring this back from the dead :D
So I went for emissions yesterday and took my laptop with me to do live A/F correction. The tester had zero issues with my adjustments during the test ...
I want to bring this back from the dead :D
So I went for emissions yesterday and took my laptop with me to do live A/F correction. The tester had zero issues with my adjustments during the test ...
Correct, It seems dot 4 has a high boiling point, but really, you should use whatever is compatible with your vehicle :)
..........You really didn't miss much other than GTRs running 8s and 9s with A/C on.......
Low FWD Nissan turnout sadly
Buy from Keo with confidence :D
Also, to note Charles (I was mentioning this last night). I wouldn't go with BC again as (which is evidence here), the blanks they use are of curpar quality.
Buy from Keo with confidence :D
Also, to note Charles (I was mentioning this last night). I wouldn't go with BC again as (which is evidence here), the blanks they use are of curpar quality.
^^ Yeah, it's called Advaned Design, Penske, Motion Control, JRZ, etc ;)
Any of those guys, with enough $$$$ flashed in thier face will make you whatever set you like. Last I checked, you could ...
The paragraph above unfortunately Jerrick is where I have my doubts about this setup
1) It is Cross TALK NOT cross walk. Simple enough mistake, so I will not delve too deeply into this one.
2) The...
I have asked several legitimate questions that the OP has seemingly avoided.
Now tell me udunnome, if I was a potential customer that had a proper reason to purchase his system, why would I even...
I have a legitimate question: With the amount of adjustment (what, 32 way or whatever it is??) how much cross talk between rebound and bound is there?? Also, depending on what customers want, how m...
Couldn't agree with you more Ben!
MeisterR
650 front and rear springs on Koni 8611s/Koni Yellows with a half cage and they rode better than any crap D2, K-Sport, whatever other rubbish out there...
Couldn't agree with you more Ben!
MeisterR
650 front and rear springs on Koni 8611s/Koni Yellows with a half cage and they rode better than any crap D2, K-Sport, whatever other rubbish out there...
Keo won't have any vacation built up in a year, although his new job has less hours, and more vacation??
The escuses keep rolling :rofl:
If you are limited on funds, a VVL may not the the way to go as it's not exactly a "direct" swap and a few additional cost items are needed for the swap to operate correctly and through the range (...
dganic23 I sure hope you are not accusing me of any of those things (not sure why you are quoting my posts) as my posting clearly states "I am NOT siding with anyone on this". I am only addressing...
What he is trying to say is, there is NO place for personal attacks in this discussion. I am not siding with anyone, but you have overstepped your grounds by your prior post. I understand you are u...
What he is trying to say is, there is NO place for personal attacks in this discussion. I am not siding with anyone, but you have overstepped your grounds by your prior post. I understand you are u...
1) The dyno puts no where near the load a full on drag slick launch would
2) From my understanding, Ashton only got 3 runs. 1st bogged hard. 2nd launched hard. 3rd, broke (supposed) oil pump
Ye...
Benjamin is (and has for past events) bringing a bimmer, why can't other previous SR owners bring other vehicles as well :dunno: .
That shouldn't be an excuse :poke: