LOl Dre. I think I also spoke with you while I was putting this setup together. I know some people were using them and not talking about it. It was people like you and charles that gave me the info...
Snickers advised me to run the p12 20v cams. I had n1's like you on my n/a motor. Those cams were pulled and sold when I boosted the motor. As miko stated sr16ve cams or p12 20v.
Did you take off the vband flange adapter? It was zip tied to the waste gate flange. Tuning time is very expensive. I know the p12's work. I know the sr16's will work. I am not sure the n1's will w...
shawn those cheap meters are not very accurate. A good multimeter can be used to diagnose all kinds of electrical issues. I would suggest some thing made by fluke. the 112 is a good cheaper unit bu...
Snickers advised me to run the p12 20v cams. I had n1's like you on my n/a motor. Those cams were pulled and sold when I boosted the motor. As miko stated sr16ve cams or p12 20v.
Snickers advised me to run the p12 20v cams. I had n1's like you on my n/a motor. Those cams were pulled and sold when I boosted the motor. As miko stated sr16ve cams or p12 20v.
Niceee. Then you will hit the tunnels. I would like to do a "Top Gear" run in the tunnels. I still might make it to this years convention. I am finally ready to get back to work after my foot surgery.
the rods need to be machined to accept the 19mm rod bearing. Most any machine shop can do this. Some of the higher hp rods come machined for the 19mm bearings.
tear the motor apart and figure out what happened. I ran my jdm de at 350whp for 5 years. It was still good when i took it apart to steal the crank and girdle. good tuning will make things last.
Knock sensors sucked on the 2001 and up models. They were unable to tell the difference between knock and normal valve train noise. I had to remove the knock sensor on my 2002 spec v to keep it fro...
tear the motor apart and figure out what happened. I ran my jdm de at 350whp for 5 years. It was still good when i took it apart to steal the crank and girdle. good tuning will make things last.
I figured I would give a update. I have the car completely back together and drove it around. I can tell you I have no boost creep out of this design. The spool up is better than I expected conside...
I will be putting the car back together tomorrow. I finished up the ic piping today. As stated the hot and cold need to be on the same side.
[url= URL=http://s31.photobucket.com/user/cortrim1/med...
Yeah after I spoke with John I realized it is such a tight space it will be tough to come up with a solution that suits every setup. What I have in mind would require the use of a custom steel fron...
Mishimoto radiators are about the same size as the koyo. I have a couple ideas for making the waste gate fit with a koyo but this will not work for all since I have a custom steel front mount which...
Installed a new aem 320lph pump. Only nicked my hand one time on the gas tank which is a new record for me. One thing I noticed is the aem pump operates much quieter than the old walboro pump it re...
I figured I would give a update. I have the car completely back together and drove it around. I can tell you I have no boost creep out of this design. The spool up is better than I expected conside...
I figured I would give a update. I have the car completely back together and drove it around. I can tell you I have no boost creep out of this design. The spool up is better than I expected conside...
Starting working on a cooling plate for the b13. Had to make if fit different due to the front grill attaching different then stock. Not too bad for left over materials in my garage.
Starting working on a cooling plate for the b13. Had to make if fit different due to the front grill attaching different then stock. Not too bad for left over materials in my garage.
I figured I would give a update. I have the car completely back together and drove it around. I can tell you I have no boost creep out of this design. The spool up is better than I expected conside...
I figured I would give a update. I have the car completely back together and drove it around. I can tell you I have no boost creep out of this design. The spool up is better than I expected conside...
Contains unread posts
Contains no unread posts
Thread is closed
You have posted in this thread
Back to top