cortrim1's Likes Received

sounds like you have a issue. I have had at least 4 t28's of various sizes over 10 years and never had a failure.

went out to the woods to work on my boys 72 Chevelle SS with a lq9 swap. So I took a picture of the car with a scenic back drop.

http://i31.photobucket.com/albums/c393/cortrim1/20130406_163849_z...

went out to the woods to work on my boys 72 Chevelle SS with a lq9 swap. So I took a picture of the car with a scenic back drop.

http://i31.photobucket.com/albums/c393/cortrim1/20130406_163849_z...

it will be fine.

it will be fine.

You have some very nice toys sir. I would pm Ziptied he had a s13 with a z32 tranny and could give all the info you need on how to make it work. On the head studs 1/2 are not even needed at 500whp ...

arp studs do not have a dog point so they don't bottom out in the block. Mazworx currently makes head studs in a 1/2 and 11mm size. Theirs are made by arp but are designed to bottom out in the bloc...

I run 20w50 vr1 conventional in my car. Great oil pressure even after several hours on the dyno.

went out to the woods to work on my boys 72 Chevelle SS with a lq9 swap. So I took a picture of the car with a scenic back drop.

http://i31.photobucket.com/albums/c393/cortrim1/20130406_163849_z...

went out to the woods to work on my boys 72 Chevelle SS with a lq9 swap. So I took a picture of the car with a scenic back drop.

http://i31.photobucket.com/albums/c393/cortrim1/20130406_163849_z...

Installed new Ultra Racing strut bar. Its lighter that the strut bar I took off and is made way better.

http://i31.photobucket.com/albums/c393/cortrim1/20130328_174428_zps0b64a0c9.jpg
http://i3...

installed the rear cut off switch so I can pass tech inspection at the convention. I also set it up so it was easy to wire the switch out of the circuit. that way the switch will only be connected ...

I am running 2 12" slim fans both have the factory plugs wired in so they connect like the factory fans. A ben mentioned only one of the factory fans has a pig tail. the other fan will need to take...

I bought it off ebay but it shipped from the factory in malaysia. So keep in none of the places that sell ultra racing actually stock them from what I found. expect it to take about 10 days to arrive.

they are reusable if in good condition. I have never had a issue with reusing a exhaust gasket.

good deal. one less thing to worry about.

Installed new Ultra Racing strut bar. Its lighter that the strut bar I took off and is made way better.

http://i31.photobucket.com/albums/c393/cortrim1/20130328_174428_zps0b64a0c9.jpg
http://i3...

Worth a try. I hope you get this sorted. I will be moving to id1000's with the next turbo setup.

you should use a head gasket to protect the mating surfaces while your measuring. You can also torque down the mls head gasket with the ge head studs. I took my motor apart three times before I was...

they are reusable if in good condition. I have never had a issue with reusing a exhaust gasket.

installed the rear cut off switch so I can pass tech inspection at the convention. I also set it up so it was easy to wire the switch out of the circuit. that way the switch will only be connected ...

Pulled it out and washed the pollen off.
http://i31.photobucket.com/albums/c393/cortrim1/20130309_152605_zps684ca5bd.jpg
http://i31.photobucket.com/albums/c393/cortrim1/20130309_152539_zps420dc16...

Pulled it out and washed the pollen off.
http://i31.photobucket.com/albums/c393/cortrim1/20130309_152605_zps684ca5bd.jpg
http://i31.photobucket.com/albums/c393/cortrim1/20130309_152539_zps420dc16...

Pulled it out and washed the pollen off.
http://i31.photobucket.com/albums/c393/cortrim1/20130309_152605_zps684ca5bd.jpg
http://i31.photobucket.com/albums/c393/cortrim1/20130309_152539_zps420dc16...

Pulled it out and washed the pollen off.
http://i31.photobucket.com/albums/c393/cortrim1/20130309_152605_zps684ca5bd.jpg
http://i31.photobucket.com/albums/c393/cortrim1/20130309_152539_zps420dc16...