All posts where ebinkerd has mentioned other members
The 5vref used to power the TPS and MAF is the power source I used during prototyping. It works surprisingly well too. But it wont be a permanent design change. The board does have a 5v regulator b...
Base: 259 Current: 700 Alternate: 588 It really was that simple. It took some smoothing out due to the larger injectors and cams, but I was idling around 1000rpm. Maybe eggman will be so kind and u...
From what I have read its mainly hardware changes and the addition of "Flex Fuel". OnTheChip JKTUNING.
From what I have read its mainly hardware changes and the addition of "Flex Fuel". OnTheChip JKTUNING.
JKTUNING OnTheChip
JKTUNING OnTheChip
D-Unit121 wouldn't you be better off using the EBC setup then? Reduced power is reduced power. It shouldn't matter if its 1lb or 2lb on the boost or 5 degrees timing. Setup the boost by gear and yo...
crznx2000 is pretty damn knowledgeable on the conversion.
SE-RMonkey keep us updated. I have three ac jobs I'll be doing this weekend all dealing with leaks. I'll try to post some pics and details that may help any one. Also, vacuum for 15min is sufficien...
manuelmora My controller will work with the Emanage. And it looks to be a good platform to work with considering the functionality of emanage. As long as the emanage can change coil dwell like the ...
The short answer is no, you cannot run the RWD ecu with distributor ignition, the long and answer is if you are clever you can. If you need to run off the distributor for the time being, use the FW...
Dala Is this compatible with E100?
Y2KG20 I briefly considered putting together a kit using just the basics. But the cost of everything needed is so cheap. Even with my own circuit printing equipment, these arduinos are still made c...
D-Unit121 how close was the analyzer to the ethanol rating. I'm curious due to changes in winter and summer blend consistency.
A reschedule looks to be a good option. Wouldnt that mean JKTUNING can make it?
Never in my life would I have believed I would be where I am with this project. I am incredibly grateful for all the interest this community has shown. I am personally grateful to John at JK Tuning...
LANCESR20 Granted they fit, but they are not long enough. Unless you are using a coil that is longer version. The part numbers supplied are for the coils that are the same length as the rwd sr20det...
P10 Goodness, its been fun and I can say I have learned a lot about the ignition systems through this and that information is invaluable. I think the pricing will be very reasonable, even for this ...
P10 Goodness, its been fun and I can say I have learned a lot about the ignition systems through this and that information is invaluable. I think the pricing will be very reasonable, even for this ...
Boosted_S13 I like the MAP system for the simplicity. Overall though, calculating density based on pressure and temp is, IMO, much more effective than a heated wire. With this, it comes down to pr...
nismo94tuner, are you taking about the wire that goes from the ignitor to the coil, then ecu (also the tach signal)? Or the signal from the ECU to ignitor?
Thank you Y2KG20. I've followed your build and you have put a lot of money in to it. I am glad to see you know where to put your money and where to save. If anyone has noticed yet, the physical sen...
LANCESR20 even though it took you 4 years to come forward with the info.
Just breaking your balls.
4 years LANCESR20, 4 YEARS the people have waited. Haha, anyways yeah it looks to be very promising. Here are a few pictures of why swapping shafts will not be needed. It has to do with the mountin...
I think I just found it. Maybe. I'm gonna order one and let you know.
I just realized he posted that 4 years ago. So much for the follow through.