Storm88000's Likes Given

It dyno'ed 147 whp with a 2 3/4" intake tube/bpi flow stack, 2" ssac collector header, and 2.36" hks exhaust. Hasn't been on a dyno since then.

Search my user name on the other forum for the threa...

:bigthumbup:

Just to put some closure on this thread.

The tool from mazworx worked great, my engine is fully timed and ready to go.

keep it stock, don't go aftermarket. if you replace, use oem parts only. full concourse cars are rare these days.

If the car sat very long the compression will be low. I have had engines come in with 30-80psi at first. Timing chain needs to be verified in 3 points. Crank/Intake cam/Exhaust cam. Most chains hav...

doesnt even have a driver seat just sits on a bucket

im putting a de in and bracket racing screw this

I thought the Convention was in Cleveland every other year. I cannot plan that far in advance right now, but I do love a Jersey tomato.

Here is my other SE-R. The mechanics at the dealership laug...

Any chance we might see this beauty at the [url= URL=http://www.sr20-forum.com/2016-national-convention-new-jersey/79244-updated-sr2016-convention-info.html]convention[/url]?

Without any new information towards the case at hand, this thread will now be locked.

Basically, remember what Mama said......

https://57.media.tumblr.com/7a9220f249a717c85c9348818a4eab18/tu...

I'm moreso curious why you think a B15 tranny swap is a "preposterous" idea. With a new transmission comes a new (likely bigger) clutch disk... no?

Did something cosmetic
[url= URL=http://smg.photobucket.com/user/TRUSE-R/media/1BABF0F9-2A0B-4B46-8218-8E5B54DC9BD4_zpstmlelisu.jpg.html][img]http://img.photobucket.com/albums/v175/TRUSE-R/1BABF0F...

Thanks again for the kind words... I was really surprised to have dropped .6s and gain about 5mph in the 1/4 mile with weight reduction and cams. The motor is completely stock JDM SR20DE except fo...

My stock block SR20DE Updated times!

Great posts Yosho and blusteelsr20.

It has been hard to keep pressing forward with my build. I am still very bitter, upset and disillusioned.

All the parts I require are here except for one (1...

Shawn I just bought a 1.6 car to use for parts for my track car build...
If u want the Ac line I will send it out to u.

I like the progress ;)

It's easier than you'd think. When I installed underdrive stuff i did this trick;

-I put all the pulleys in place, and wrapped a string around the pulleys
-I then measured the string (31.49",[800...

[url= URL=http://www.ebay.com/itm/Nissan-Sentra-NX-Coupe-Factory-Service-Manual-1991-/161798587844?hash=item25abf285c4&vxp=mtr]FSM[/url]

$36 shipped...GET IT!!! This is one tool you will ALWAYS...

I'm sorry, I might be a little wrong on the temp sensor information as its been quite a while since I've even touched an OBD2 engine. It might use two sensors, one for the gauge and one for the ECU...

This had nothing to do with this particular transaction, NO, you are correct. HOWEVER, this thread isn't just for this transaction, this is a feedback thread for Jordan. Those who do business with ...

^^^^^holy shit dude get off his nuts already!!!!

Since I dont see an end in sight for this thread and it will most likely be referenced in the future with people dealing with Jordan I wanted to put this one the record.......I'm on the complete op...

After the initial shock wore off, he posted that it wasn't as bad as he thought and the oil pan took the brunt of the damage. He cooled down after a few days after he realized a new oil pan would b...

According to Jordan he listed the header for "local pick-up", and with that intent, having a potential buyer come to his home and check it out in person, did he really approach any line? We know no...

Here was the physical description from the original sale thread:
"Good shape, i'd say 7/10. No holes or rust."

And the image just for completeness: https://i.imgur.com/TIwDXur.jpg


First off, I t...