nsusammyeb's Likes Received

turbotank still makes the maf housings and they are badass.

turbotank still makes the maf housings and they are badass.

Got some numbers on one of mine finally.

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg1_zps67b73ec3.jpg.html][img]http://i71.photobucket.com/albums/i147/nsusammyeb/imagej...

The furthest from the origin will always have less pressure. Simple known fact. If the holes are too large you'll lose a lot of pressure at the end of the rail. Have you seen the size of the hol...

Already done, there's a thread called "let's talk catch cans."

You can drill these out as well guys. I use a blue point carb jet drill on mine. You can do it by hand. Iirc it was like .040" that I used last time. Just pressurize the rail with some compress...

I think everyone let out the first pass. I didn't know where the line was either, hence the low mph and et.

Smurf in the left, me in the right@12psi

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg6_zps9b463a11.jpg.html][img]http://i71.photobucket.com/albums/i147/nsusammyeb/imagejpg6_...

We already have a manifold that performs well. Center fed or side fed...your choice.

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg4_zps57f06fb4.jpg.html][img]http://i71.photobucket.com/albums/i147/nsusammyeb/imagejpg4_zps57f06fb4.jpg[/img][/url]

[url= URL=h...

vqman

Dyno at Ohio convention with SR20GTi-R at the helm.

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg1_zps5aed0968.jpg.html][img]http://i71.photobucket.com/albums/i1...

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg2_zpsbd750f3f.jpg.html][img]http://i71.photobucket.com/albums/i147/nsusammyeb/imagejpg2_zpsbd750f3f.jpg[/img][/url]

Time slip fro...

Clutch Masters Dealer

Local 1/8 mile this weekend to work on the first half of the track. It went 7.5 with a 1.76 60' last year on the b14 gearbox. At convention it only went 7.7 with a 1.66, 60'. I'm thinking I need ...

Local 1/8 mile this weekend to work on the first half of the track. It went 7.5 with a 1.76 60' last year on the b14 gearbox. At convention it only went 7.7 with a 1.66, 60'. I'm thinking I need ...

Yessir. Looking forward to it.

Test n tune Friday. :)

Test n tune Friday. :)

Looking good Chris! Here's some quick D ring brackets I made for the new dyno.

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg1_zps4f298ea1.jpg.html][img]http://i71.photobucke...

Looking good Chris! Here's some quick D ring brackets I made for the new dyno.

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg1_zps4f298ea1.jpg.html][img]http://i71.photobucke...

I'm sure there are plenty of sheets around here from guys with N1's on a factory intake.

Should have hit me up. Could have gotten it cheaper.

vqman

Dyno at Ohio convention with SR20GTi-R at the helm.

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg1_zps5aed0968.jpg.html][img]http://i71.photobucket.com/albums/i1...

vqman

Dyno at Ohio convention with SR20GTi-R at the helm.

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg1_zps5aed0968.jpg.html][img]http://i71.photobucket.com/albums/i1...

[url= URL=http://s71.photobucket.com/user/nsusammyeb/media/imagejpg2_zpsbd750f3f.jpg.html][img]http://i71.photobucket.com/albums/i147/nsusammyeb/imagejpg2_zpsbd750f3f.jpg[/img][/url]

Time slip fro...