Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

BenFenner's Likes Given

All posts liked by BenFenner

BenFenner's Likes Given
- All posts liked by BenFenner
Posts: 3,001-3,025 of 3,035
Thread Title / Post Title / Post Preview
Posted By / Posted At
Forum Section
Thread: 2012 Convention Info......... The Reunion!!
Post: Guys just a reminder the cut off date for the room rate i...
Guys just a reminder the cut off date for the room rate it April 30th. .... Get those rooms reserved!!
2012-04-18 16:42
Thread: A Hose To Remember For The VVL
Post: A Hose To Remember For The VVL
A Hose To Remember For The VVL
2008-11-05 12:41
Thread: How To: Make Strong Solder Joints
Post: i am 1 of those people who are mostly against crimps/butt...
i am 1 of those people who are mostly against crimps/butts.

this is how any wire joining should be done when you are unable to make a new run of wire the exact length you need it. Lineman’s/...
2012-04-17 18:20
Thread: How to check if tranny is bad?
Post: open it up and look for carnage, you might have to take i...
open it up and look for carnage, you might have to take it apart and see if there is an damage to the bell housing
2012-04-17 17:27
Thread: Where are the real budget builders?
Post: ebay turbos all day long
ebay turbos all day long
2012-04-17 15:30
Thread: Lynch's 6spd / VE-T thread
Post: OOOO rooky rooky what just showed up! http://i49.photo...
OOOO rooky rooky what just showed up!

http://i49.photobucket.com/albums/f285/lynch420/turbo/IMG00515-20120416-1819.jpg
2012-04-17 01:22
2012-04-17 12:18
Thread: What's A Good Set Of Rod Bearings To Get ?
Post: Prolly needs an oil pump also, or check the pan and make ...
Prolly needs an oil pump also, or check the pan and make sure its not pushed up against the pickup tube
2012-04-09 00:37
Thread: What's A Good Set Of Rod Bearings To Get ?
Post: The oil light is considered an "idiot light" it comes on ...
The oil light is considered an "idiot light" it comes on at around 2-5 psi, I would def look farther into things.

Especially if you know the level was correct, something else is going wrong, unle...
2012-04-08 23:14
Thread: What's A Good Set Of Rod Bearings To Get ?
Post: What caused the issue first? Dont go throwing money at it...
What caused the issue first? Dont go throwing money at it without figuring out how it started...lack of oil changes, driving it with low oil levels, high milage, just purely getting the ish pounded...
2012-04-08 17:07
2012-04-07 20:15
Thread: my turbo
Post: If it has that much shaft play have it rebuilt now.
If it has that much shaft play have it rebuilt now.
2012-04-17 00:46
Thread: 15 x 8 +22
Post: Guys rolling the fenders doesnt FLARE them. It just fold...
Guys rolling the fenders doesnt FLARE them.
It just folds the lip in so it is a tight "U" shape,not "L" shape if you know what I mean.
It wont effect the body lines,it just gives you about 1/2 in...
2011-10-24 06:15
Thread: Pulsar GTi-R Revamped....
Post: Its been a lot of work in the making. Alot of the problem...
Its been a lot of work in the making. Alot of the problems have come from transmission issues. Making the power is not a problem. When we first got the car, it honestly was a huge mess but spending...
2012-04-16 14:08
Thread: Fender Flares on a B13....
Post: My buddy Mark Fatboyse-r, it'll be at the convention. ht...
My buddy Mark Fatboyse-r, it'll be at the convention.

http://www.jklmn.net/albums/track_ready/IMG_1352.sized.jpg

C
2012-04-16 16:22
Thread: Lower arm, cross threaded lower arm bolt to chassis
Post: You have one bolt holding the rear part of the control ar...
You have one bolt holding the rear part of the control arm in and you're considering driving it that way? Dude, it's time to get clean and sober. :poke:

Retap the hole and get a new bolt in ther...
2012-04-15 12:03
Thread: Pulsar GTi-R Revamped....
Post: And straight cut gears just sound so damn manlyyyyy!!! :D
And straight cut gears just sound so damn manlyyyyy!!! :D
2012-01-19 17:21
Thread: PAR Gear Sets Getting Ready To Be Shipped
Post: PAR Gear Sets Getting Ready To Be Shipped
PAR Gear Sets Getting Ready To Be Shipped
2012-03-22 16:09
Thread: 16/20VE Shim Clearance
Post: Sharing with my "internet buddies", friends and "enemies"...
Sharing with my "internet buddies", friends and "enemies"

http://i189.photobucket.com/albums/z174/N1inSight/FSM/page74.jpg

http://i189.photobucket.com/albums/z174/N1inSight/FSM/page75.jpg

...
2009-05-11 23:29
Thread: s4's kinda pointless with t25...
Post: I really don't know where this lost in mid is coming from...
I really don't know where this lost in mid is coming from. I think people are confusing the gain from the top and think that it is loss in the mid range? IDK
2012-04-13 16:33
Thread: s4's kinda pointless with t25...
Post: S4s make more power than stock from idle to rev limit.
S4s make more power than stock from idle to rev limit.
2012-04-13 02:03
Thread: Painting the Cusco FSTB
Post: hmmm. you really tried to go hard. my intentions were to ...
hmmm. you really tried to go hard. my intentions were to not be a "hater." but since you wanna go there. take a look at my nx and then take a look at yours, why the **** would i hate ? my stillen v...
2009-01-24 18:26
Thread: Brakes+Gauges=?
Post: Guess I should have searched a little harder. http://w...
Guess I should have searched a little harder.

http://www.sr20-forum.com/general-sr20/25156-wierd-problem-electrical-tach-lights-come-when-brake-pedal-pushed.html

:)
2012-04-12 20:22
Thread: 2012 Convention Attendance Roster
Post: I just want to be related to Ben :dunno:
I just want to be related to Ben :dunno:
2012-03-29 23:39
Thread: World's Quickest and Fastest Nissan
Post: Who said there wasn't?
Who said there wasn't?
2012-04-11 07:01
Icon Legend and Forum Information
Contains unread posts
Contains no unread posts
Thread is closed
You have posted in this thread
Users Browsing this Forum
There are currently ? users browsing this forum. (? members & ? guests)
StubUserName

Back to top