eggman's Likes Given

Never in my life would I have believed I would be where I am with this project. I am incredibly grateful for all the interest this community has shown. I am personally grateful to John at JK Tuning...

The Beetle needed a new headlight, and when replacing it I found the wiring in bad shape. I guess heat from the bulb and German sheathing don't mix. [url= URL=https://www.facebook.com/media/set/?se...

Jay,

Certainly entertain a VET headgasket.

Certainly entertain upgrading headstuds while you are there. Whatever your wallet can afford. Lots of silvia boys have had problems with the ARP so...

I went over this with another forum member about a year ago thinking 3 amps would be fine because the internets said about 2.8 amps. Turned out having vvl breakup due to the window switch. Just s...

Both of my B13s get it done in the loose stuff. Outperformed the entire field of cars at a Snowcross this past weekend, AWD Turbo cars included!

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak...

Ok I just heard back from ARP on this matter.

12mm ARP head studs are made from the 8740 material

11mm ARP head studs are made from ARP2000

Both studs are designed to work on all sr20, m...

Installed new left and right LCAs, complete with new ball joints, as well as new MOOG outer tie rod ends....on DDB

Finally got to use my new tool that everyone should have in their repertoire......

When the hub falls off with the removal of the caliper.... Its bad

Jay,

VET headgasket with Mazworx headstuds.... End of story.

Just clean it up really good and throw a VET head gasket ($75) and ARP head studs ($140). Good until the rods bend... Both are reusable after you pop the engine too :)

There was no road course day in 2011 or 2014 and that stuff is my bread and butter but neither stopped me from showing up and having a fun time.

I really wanted to not have to use hood pins/latches either but I picked a set of these up a lil while ago to see if there was a way I could stealth mount them. Haven't really played around with th...

[url= URL=http://www.quik-latch.com/lexus-IS300-mini-quik-latch-install.html]Pics on a CF hood...[/url]

Seems all the hood latch folks gravitate to aerocatch. I just don't want to drill the carbon, but the frame underneath wouldn't bother me. Has anyone ever tried mounting the pins underneath? I imag...

Ok courtesy of White steve fro CT here are the P10 flare pics... The pics don't do it any justice though, I really need to wait till the weather gets warmer and melts all this crap we have here, s...

Just picked up a set for my P10 from White steve fro CT.... Well worth it, he has some pics of the test fit, but I will be putting them on tomorrow so there will be more pics... I'm running 15x8 et...

LOL, thanks for posting them Keo. Those pics were last weeks progress on the second fixture. Both the stabilizer and selector fixtures are done! I'll be yanking the b13 linkage off my car this week...

[size= SIZE=4]Windshield is finally on!!![/size]
[url= URL=http://s531.photobucket.com/user/MADTEC/media/PULSAR%20GTI-R/Pulsar%20-%20Exterior/20150123_165108_zpsfuzyaosz.jpg.html][img]http://i531....

Def make sure you got the starter bolts out. One is very close to a tranny bolt. I dont get it either, once those 2 bolts are removed it usually falls out under its own weight. I always have ...

Will try this tomorrow. My help is gone and I start a new job in the morning so I am driving a Saab convertible as my winter daily right meow, lol.

Thanks all for the quick suggestions and help....

Installed b15 trans.

https://encrypted-tbn1.gstatic.com/images?q=tbn:ANd9GcTVoKEGXjOcfepCNbTbEaaE0lbwbJXRRNemGfzWXfQr-7oqy66G

Tungsten 6UL on black car with carbon hood and trunk must look great. I'll likely get a s...

@ speedricer it's almost there, I'll take $ when it's ready to go.

finished the stabilizer fixture a few mins ago. now onto the selector fixture!
http://turbofx.net/wp-content/uploads/2015/01/...

http://thumbs3.ebaystatic.com/d/l225/m/mwcjj4SnU6OBhplkcrkqefQ.jpg
:rockon:

Thanks for the interest everyone :) Right now I'm focusing on the fixture fabrication so I can pick up on the OEM mounting locations, which will make it easier to reproduce them for ya. I'll try a ...