Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: SR20ve swap b13 No Start Need Help!!

+ Reply To Thread
Posts: 1-10 of 10
2015-02-11 02:52:19
#1
SR20ve swap b13 No Start Need Help!!
Ive just gotten my Ve swap ready to start but it WONT. I have power at the starter but no signal from the small wire(understood that its supposed to receive a 12v signal when the ignition is turned). I was able to jump the solenoid with a screwdriver and it turns over but doesn't start. My relays are good and fuses are not blown. I have enough grounds and fuel pressure with spark. As far as it not starting by the ignition, Im thinking I made need a new ignition because of no signal being received at the starter.Any help is greatly appreciated, so much that whoever gives me the correct solution to my issue wil have their choice of a die cast gtr model, half used calvin kleain cologne or a stooped frooty iced out watch that will pull all the shortys at the club yo!. I seriously need some assistance, I want to hear my swap purr for its first time, Below are some leftover wires that I have that aren't connected and I assume I don't need any of them, but if Im wrong can someone lmk where they go, thanks for all help!!![img][URL=http://s1382.photobucket.com/user/calikid89b13/media/plug_zpsjtfpypdn.jpg.html][IMG]
http://i1382.photobucket.com/albums/ah266/calikid89b13/plug_zpsjtfpypdn.jpg[/img][/URL][/IMG]
[img][URL=http://s1382.photobucket.com/user/calikid89b13/media/photo%201_zps8ddvjatx.jpg.html][IMG]
http://i1382.photobucket.com/albums/ah266/calikid89b13/photo%201_zps8ddvjatx.jpg[/img][/URL][/IMG]
[img][URL=http://s1382.photobucket.com/user/calikid89b13/media/photo%202_zps1st3n2lo.jpg.html][IMG]http://i1382.photobucket.com/albums/ah266/calikid89b13/photo%202_zps1st3n2lo.jpg[/img][/URL][/IMG]
[img][URL=http://s1382.photobucket.com/user/calikid89b13/media/plug3_zpsag9kawiq.jpg.html][IMG]http://i1382.photobucket.com/albums/ah266/calikid89b13/plug3_zpsag9kawiq.jpg[/img][/URL][/IMG]
[img][URL=http://s1382.photobucket.com/user/calikid89b13/media/plug%202_zps3lamaa9v.jpg.html][IMG]http://i1382.photobucket.com/albums/ah266/calikid89b13/plug%202_zps3lamaa9v.jpg[/img][/URL][/IMG]
[img][URL=http://s1382.photobucket.com/user/calikid89b13/media/photo%204_zpsmudhgl1a.jpg.html][IMG]http://i1382.photobucket.com/albums/ah266/calikid89b13/photo%204_zpsmudhgl1a.jpg[/img][/URL][/IMG]
2015-02-11 09:21:53
#2
having just done a ve swap myself, i'd guess that the two left over pins are the egr and the ficv. keep these to fire your vvl solenoids should you aquire nismotronic SA one day.

single yellow wire no idea sorry.

you have fuel pressure,spark,injector pulse? is the fuel getting to the plugs?

if not maybe your injectors are blocked from stale fuel?

that was my issue. gentle tap on the top of the fuel rail injector caps, and presto.
2015-02-11 11:24:32
#3
S20ve swap help
I will try that today and see if it solves my issue, Ill keep you posted, thanks!
2015-02-11 13:11:37
#4
3rd picture is your problem. should be a plug that goes into it to connect the 2 harness together

2nd picture is egr crap
Last edited by morgans432 on 2015-02-11 at 13-13-03.
2015-02-12 15:29:50
#5
CalKid where are located? you in socal? If so and you can't get it going I can come help if you're not too far... But check for power at your injectors, coil, dizzy.. all critical to run.. start. with that.. also power at pin 36 on the ecu assuming obd1 also check pin 47 for power post eccs relay.. so 36 is ign sw and it opens a ground at pin 4 aka neg to eccs then powers harness and provides main power to pin 47.. 47 is really the one to check..
2015-02-12 15:31:59
#6
if you get power to all of that check injector NEG trigger back to ECU if you get nothing then look to the CAS to be the problem.. I build my own ECUs I had to figure out everything with the wiring.. lol
2015-02-14 04:36:04
#7
Thanks for the advice man, Ill def. check it out tomorrow, it still has no signal to starter but the relay clicks when ignition is turned, I live in SC btw ha, used to be in socal.
2015-02-14 15:22:36
#8
last pic looks like the starter ground plug to me
2015-02-14 16:45:07
#9
SR20ve swap b13 No Start Need Help!!
Originally Posted by eggman
last pic looks like the starter ground plug to me

starter grounds at engine via contact to the trans and bolts.. what you mean starter ground plug?
2015-02-14 17:36:52
#10
Originally Posted by shagspeed
Originally Posted by eggman
last pic looks like the starter ground plug to me

starter grounds at engine via contact to the trans and bolts.. what you mean starter ground plug?


OK ,well theres a bolt that the battery connects to with a nut ...then theres the wire that has to plug in to the harness...I thought it was a ground but I guess not. I edited my post as to not cause any more confusion ,Sorry for trying to help,not put false info out there.
Doesnt matter if its ground or not,it needs to be hooked up,that was my point.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top