![](/images/threads/icons/0.png)
****MAY 2nd, 2013 update****
SR20VE head gasket swap is complete:
- I went with the thicker one from Greg normally used for VE turbo applications, but less likely to fail over time. This may have lowered power a bit, however this job was a huge pain in the arse, and I'd rather lose a few HP than do this again.
- The head was re-surfaced at a machine shop, it ended up being about 1/15 thousandth of an inch off.
- All new Nissan OEM head studs, no APR stuff. Too many horror stories
- They also cleaned and chased all the holes because one of the head studs failed
- Three angle valve job
- Port and polished head and all the goodies
- New VC gasket
- I also wired two new radiator fans directly to a switch inside the cabin, bypassing the ECU because of an apparent short.
Here are lots of before and after photos:
.
.
Head first pulled after gasket failed:
![](http://img.photobucket.com/albums/v87/Storm88000/headoff_zpsd1c71834.jpg)
.
.
Cleaned up, new head gasket on:
![](http://img.photobucket.com/albums/v87/Storm88000/newgasket_zpsf31f7c36.jpg)
.
.
Before:
![](http://img.photobucket.com/albums/v87/Storm88000/IMG952153_zpse1209e32.jpg)
![](http://img.photobucket.com/albums/v87/Storm88000/insidve_zps8920379c.jpg)
.
.
After:
![](http://img.photobucket.com/albums/v87/Storm88000/d0257ada-7d2b-4277-ad47-45dba8a5aeea_zps5b0f7481.jpg)
![](http://img.photobucket.com/albums/v87/Storm88000/measurementsmar20_zps93b5c6ed.jpg)
![](http://img.photobucket.com/albums/v87/Storm88000/valves_zps29b14284.jpg)
![](http://img.photobucket.com/albums/v87/Storm88000/219b_zps186902ab.jpg)
.
.
SO.. I will be going to the very same dyno again this weekend. Previously, before the head gasket failed, the motor made 206hp @ 7920RPM and 148 ft-lbs of torque.
Any guestimates of what it could make now? It was a pretty thorough port and polish, and driving it now after the break in period, I certainly feel a difference up high, not a huge amount, but some. I'm wondering if the thicker head gasket may have kinda offset the port and polish, who knows. I stuck with the original intake manifold although I briefly considered purchasing the kit from Greg, but it was too expensive and would have put the project over what I wanted to spend.
With everything back together, just before the valve cover was put back on. Really clean motor, no sludge. I run only Mobil-1 synthetic
(I know some of you don't like that but its worked for me)
![](http://img.photobucket.com/albums/v87/Storm88000/vecoveroff23_zps8dd873fb.jpg)
.
.
All in all, it took about a month of working on it here and there, when the weather cooperated (it even snowed a few times).
Here she is now, looking and running good from yesterday:
SR20VE head gasket swap is complete:
- I went with the thicker one from Greg normally used for VE turbo applications, but less likely to fail over time. This may have lowered power a bit, however this job was a huge pain in the arse, and I'd rather lose a few HP than do this again.
- The head was re-surfaced at a machine shop, it ended up being about 1/15 thousandth of an inch off.
- All new Nissan OEM head studs, no APR stuff. Too many horror stories
- They also cleaned and chased all the holes because one of the head studs failed
- Three angle valve job
- Port and polished head and all the goodies
- New VC gasket
- I also wired two new radiator fans directly to a switch inside the cabin, bypassing the ECU because of an apparent short.
Here are lots of before and after photos:
.
.
Head first pulled after gasket failed:
![](http://img.photobucket.com/albums/v87/Storm88000/headoff_zpsd1c71834.jpg)
.
.
Cleaned up, new head gasket on:
![](http://img.photobucket.com/albums/v87/Storm88000/newgasket_zpsf31f7c36.jpg)
.
.
Before:
![](http://img.photobucket.com/albums/v87/Storm88000/IMG952153_zpse1209e32.jpg)
![](http://img.photobucket.com/albums/v87/Storm88000/insidve_zps8920379c.jpg)
.
.
After:
![](http://img.photobucket.com/albums/v87/Storm88000/d0257ada-7d2b-4277-ad47-45dba8a5aeea_zps5b0f7481.jpg)
![](http://img.photobucket.com/albums/v87/Storm88000/measurementsmar20_zps93b5c6ed.jpg)
![](http://img.photobucket.com/albums/v87/Storm88000/valves_zps29b14284.jpg)
![](http://img.photobucket.com/albums/v87/Storm88000/219b_zps186902ab.jpg)
.
.
SO.. I will be going to the very same dyno again this weekend. Previously, before the head gasket failed, the motor made 206hp @ 7920RPM and 148 ft-lbs of torque.
Any guestimates of what it could make now? It was a pretty thorough port and polish, and driving it now after the break in period, I certainly feel a difference up high, not a huge amount, but some. I'm wondering if the thicker head gasket may have kinda offset the port and polish, who knows. I stuck with the original intake manifold although I briefly considered purchasing the kit from Greg, but it was too expensive and would have put the project over what I wanted to spend.
With everything back together, just before the valve cover was put back on. Really clean motor, no sludge. I run only Mobil-1 synthetic
![:)](images/emoji/happy/smile.gif)
![](http://img.photobucket.com/albums/v87/Storm88000/vecoveroff23_zps8dd873fb.jpg)
.
.
All in all, it took about a month of working on it here and there, when the weather cooperated (it even snowed a few times).
Here she is now, looking and running good from yesterday:
![](http://img.photobucket.com/albums/v87/Storm88000/b670e4e7-253e-4406-9c80-2abbd190aea0_zpsf4d15cb6.jpg)
Last edited by Storm88000
on 2013-05-02
at 08-44-41.