Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: My 4dr B13 Project

+ Reply To Thread
Posts: 1-10 of 74
2014-04-19 20:21:44
#1
My 4dr B13 Project
I owned a couple B13s a while back and decided that I wanted a project car. The story line:

This used to be my DD; Carb GA16DS (yes GA16DS not GA16DE, go do your research) 5spd (damn I miss her )


Then I put her under the knife because she was rusted really badly. I dropped the engine in preparation for my SR20DE Swap




The only reason I could afford to put my DD under the knife was because I acquired another B13. This one was a wreck BUT it only had front damage, the rest of the car was in immaculate condition.


The carnage


Now I call this "the merge"





Even got some fender braces made to strengthen the front



Took her to the bodyshop to get touched up and this was the result




Fitted some Versa/Tiida wheels and was satisfied with the look


Final product
Last edited by karibah on 2014-04-20 at 11-32-39. Reason: Omit
2014-04-19 20:47:33
#2
Now I wanted some rare items and couldn't find then individually so I had to buy a whole damn car to get them.

I acquired a Pulsar Gti-R RNN14 rolling chassis for my donor.




Some of you may ask, why didn't you just use the Pulsar? NO!!! The Pulsar is a lot heavier than a B13 and its more difficult to source parts for. I took the whole interior, suspension & brakes and a few other components that remained in the engine bay. Here are a few pics of what I took.






I have the body sorted out but I need a power plant , I got an SR20DE RR 10:1 from a 98 EUDM Primera complete with tranny, harness and ecu.




I busted her down to get her cleaned up and started the long and costly journey of purchasing parts.

Last edited by karibah on 2014-04-20 at 15-24-25. Reason: Editing
2014-04-19 21:14:18
#3
Now, I'm big on suspension so over the years I've acquired quite a bit of suspension pieces

OEM Suspension pieces












Floor Brace


KYB shock boots and bump stops

KYB GR2s

KYB had strut mounts too so I said, what the heck, these must be better than the OEM ones.



Road Magnet Springs


Energy Suspension and Prothane Pieces







Dog Bone Mount


Progress Rear Sway Bar


Suspension Techniques Front Sway Bar



Cusco LCAB


Cusco FSTB and eBay RSTB


The car was not originally rear disc so I had to do the conversion



Wilwood Brake Fittings

Russell Brake Fittings


Camber Bolts


Aluminium X-member Bushings


Aluminium Subframe Bushings


Megan Racing Steering Ends


Added some rotors and this is how she sits now





Last edited by karibah on 2014-04-20 at 20-52-57. Reason: Editing
2014-04-20 03:02:37
#4
Very nice! Looking forward to seeing more progress!
2014-04-20 11:22:21
#5
This post is about my engine rebuild

I a stickler for doing things the right way so I spared nothing when it came to buying components for my engine rebuild.

SE-R Motor Mounts for SR20 Swap


The plan was originally to turbo the car so I bought VET rods and pistons




and I bought a used TD05HA-152G6-12T from an Evo X; owner upgraded his turbo.




The block and head were in good condition but I decided that they needed Kariba's touch.

I started porting the RR head



Then I thought, if you're going to be putting the engine through the rigours it needs to be built tough, not Ford tough, Kariba Tough.
OEM Gasket kit with OEM Chain, OEM Tensioner, Thermal Spacer, SR20VE Metal Head Gasket, Cometic Front & Rear seals

OEM Cam Gears

OEM Seals

OEM Thrust Washers

SR20VE Front Cover Assembly


OEM Crank Gear

VVL Pickup Tube

G Spec Aluminium Pulley

ACL Bearings; I have ACL Thrust Washers as well but just can't seem to find the damn pic


ARP Bolts


ARP Flywheel Bolts


Clutch Kit



Cooling
Mishimoto Radiator hoses

NX2000 Dual Core Radiator


Water Temp Sensor Adapter

OEM Coolant Temperature Sensor


OEM Valve Cover Bolts and Washers



Fuel System
Aeromotive



OEM Injector Harness


Fuel Rail Bolt Kit


SR20VE Distributor


Magnecor Plug Leads



OEM TPS


OEM Knock Sensor


Fuel Cooler


Oil Cooler


Nissport Fitting


There may be a few other things I forgot which I'll add in later but the build starts.
8CW RR Crank with SR20VET Rods & Pistons and Girdle.




The block is already tapped just not pictured in any of the angle shots.
Last edited by karibah on 2014-04-20 at 15-57-53. Reason: Editing
2014-04-20 11:40:56
#6
Through my many purchases from Forum Members, I got these......
2014-04-20 14:24:46
#7
I had a revelation and I decided to ditch the Turbo setup and go ALL MOTOR.

So I got this.....SR20VE Head fitted with N1 Cams


and give its Kariba's Touch as well.
Intake. As you can see, I already had the head tapped with my -4AN anodized blue fitting.

Exhaust


SSAC Headers



SuperTech Valve Springs and Retainers


I had originally bought the Greddy E-manage so I'll chip my ECU and use the E-manage to fine tune.

Got the Jumper Harness so that I don't have to hack my harness.

You also need the A/F Harness for the E-manage to record your A/F ratios; this is why most people claim that it doesn't work or you can't tune accurately.


N62 MAF; I won't be using this soon because I already ordered the Greddy 3BAR MAP sensor.


Nismo CAI


Glow Shift Gauges and AEM Wideband


MSD Blaster Coil


Nismo Radiator Cap, Nismo Oil Filler Cap and -6AN Autobahn88 Fuel Rail Adapter Fitting


Dry Cell Battery
Last edited by karibah on 2014-04-20 at 20-56-38. Reason: Editing
2014-04-20 14:41:16
#8
Talk about going the distance... Nice to see someone going ALL THE WAY.
2014-04-20 15:37:29
#9
Thanks @Latino Heat & @LAM-PARK.

I actually added a few more pics to my posts. I've done extensive research and have been collecting parts for quite a few years. The knowledge gained and continue to gain is priceless. There are so many things we can do with these engines and so many components we can use if we only did a little more research.
2014-04-20 15:38:47
#10
My kaleidoscope of -AN Wrenches.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top