Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: G20 Black Leather seats

+ Reply To Thread
Posts: 11-20 of 22
2011-05-26 22:06:07
#11
if it's silver which it should be. that's the guy on here.
2011-05-26 22:20:19
#12
Originally Posted by blackb13se-r
if it's silver which it should be. that's the guy on here.


Bes used to own a red B13.
2011-05-26 23:19:36
#13
Originally Posted by ccrelan


The front seats sit up a bit higher than stock seats even with NX200 seat rails. I thought it was a nice upgrade. There is a bit more support and the seats are a good bit firmer than my se-r fronts were.


Are the NX rails the only thing needed to make the G20 seats fit?

Also, how much for your seats shipped
2011-05-26 23:54:38
#14
Originally Posted by NissanUnlimited
CHECK OUT THE NEW IMPORT TUNER MAG! b13 sr20det!! has passenger g20 seat w/ driver sparco seat!


its my car.

what i did was strip down a b13 seat down to the frame and then installed the p10 foam and leather onto it. the rear seat is a whole different story. i couldnt install one due to the cage but the bottom will fit fine. your better off getting the top of your b13 one recovered than trying to fit the p10 top part.
2011-05-27 00:30:23
#15
I have had about 5 offers to ship the seats. I honestly don't want to deal with shipping them. They are big, bulky, time consuming, and it would cost a lot of money to ship.

When I did the conversion, I had the ser side mouting tabs (that attach to the rails) welded onto the G20 pans. The g20 seat pans had support extenders that the sear pans did not.
2011-05-27 01:10:30
#16
What year g20 seats will fit??
2011-05-27 05:12:16
#17
Originally Posted by ccrelan
I have had about 5 offers to ship the seats. I honestly don't want to deal with shipping them. They are big, bulky, time consuming, and it would cost a lot of money to ship.

When I did the conversion, I had the ser side mouting tabs (that attach to the rails) welded onto the G20 pans. The g20 seat pans had support extenders that the sear pans did not.


I've shipped Bride seat before & if you lay them in the 69 position w/out rails you'll be good to go !! From Miami to Cali i payed about $100 shipped ....
2011-05-27 05:50:58
#18
If I was to go about it again, I would remove the metal bolster supports off the g20t bucket and tack weld them onto the spot of the b13 bolster support. If you just slide the leathers onto the B13 frame, it will be decent but 100%. You will see the seat is not as solid as it was on the g20 frame. Kind of hard to explain. If/when you do it and strip the seats down, you will see what I mean. I actually miss my leathers but they went off with my old classic.

As far as the rears, I started by clipping in the bottom section. I then lined up the two skinny outer cushions and pressed the two bigger inner sections in like an old cabinet door. They are a tight fit but it will work. I am 6'2'' and the seats made my head get close to the headliner without having it reclined a good amount. I would recommend the nx rails when doing this as the g20 cushions raise the seat height about an inch or so.
2011-05-27 16:03:03
#19
i have g20 back seats not leathe but grey material with arm rest and those head things lol looks and feels amazing!
2011-05-27 16:05:56
#20




+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top