how to install l.e.d. cluster lights (from liuspeed)
first u need to remove the cluster
1.remove shifter bevel
2. remove stereo/hvac bezel
3.remove bezel and metal plate below steering wheel
4.remove trim arond cluster
5.remove screws around cluster
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam025.jpg[/img][/IMG]
6.(if you have a 91,92, u will need to disconnect the speedo cable)probably the most difficult part of install hint (hint get rid of the plastic shield around the cable, makes re-installation lots easeier
7.remove the three main lights as shown
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam015.jpg[/img][/IMG]
8.take a pick tool and remove oem wire from the light socket as shown
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam010.jpg[/img][/IMG]
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam011.jpg[/img][/IMG]
9. use a flat screwdriver to push the light from the socket (they can be stuborn)
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam012.jpg[/img][/IMG]
10. u will need to rotate the wire ont the l.e.d light's 90 degrees
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam019.jpg[/img][/IMG]
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam020.jpg[/img][/IMG]
11. then just insert the bulb into the socket
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam021.jpg[/img][/IMG]
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam022.jpg[/img][/IMG]
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam023.jpg[/img][/IMG]
12.installation is a little tricky cause thease lights have polarity test them before u put it back together!!!!
13. repeat removal steps in reverse for re-assembly
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/IMG058.jpg[/img][/IMG]
and this is what u get
1.remove shifter bevel
2. remove stereo/hvac bezel
3.remove bezel and metal plate below steering wheel
4.remove trim arond cluster
5.remove screws around cluster
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam025.jpg[/img][/IMG]
6.(if you have a 91,92, u will need to disconnect the speedo cable)probably the most difficult part of install hint (hint get rid of the plastic shield around the cable, makes re-installation lots easeier
7.remove the three main lights as shown
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam015.jpg[/img][/IMG]
8.take a pick tool and remove oem wire from the light socket as shown
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam010.jpg[/img][/IMG]
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam011.jpg[/img][/IMG]
9. use a flat screwdriver to push the light from the socket (they can be stuborn)
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam012.jpg[/img][/IMG]
10. u will need to rotate the wire ont the l.e.d light's 90 degrees
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam019.jpg[/img][/IMG]
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam020.jpg[/img][/IMG]
11. then just insert the bulb into the socket
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam021.jpg[/img][/IMG]
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam022.jpg[/img][/IMG]
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/sonydigitalcam023.jpg[/img][/IMG]
12.installation is a little tricky cause thease lights have polarity test them before u put it back together!!!!
13. repeat removal steps in reverse for re-assembly
[img][IMG]http://i537.photobucket.com/albums/ff331/kyledriver87/IMG058.jpg[/img][/IMG]
and this is what u get
Last edited by kyledriver
on 2011-04-24
at 23-05-10.