Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: Can This Part Of My Transmission Be Repaired?

+ Reply To Thread
Posts: 11-20 of 21
2014-06-22 17:17:03
#11
Originally Posted by 91sentragti-r

by casing cover I mean the top cover that goes over the gear stacks and mates to the bellhousing... the oiler is the yellowish looking Plastic piece that attaches to the cover and oils the gears and bearings.. you should have no problems with the sensors.. I'm not too sure if the FSM shows the oiler, but I'm pretty sure it does..


Is that the cover I have a picture of in the first post? Because it's slightly damaged and I'm not sure if it can still be used.

Thank you!!
2014-06-22 22:06:59
#12
Was this the transmission for sale a while ago or another one?
2014-06-22 22:30:36
#13
Originally Posted by Kyle
Was this the transmission for sale a while ago or another one?


No, this transmission was never listed for sale.
2014-06-23 02:25:20
#14
Originally Posted by David99G20T
Originally Posted by 91sentragti-r

by casing cover I mean the top cover that goes over the gear stacks and mates to the bellhousing... the oiler is the yellowish looking Plastic piece that attaches to the cover and oils the gears and bearings.. you should have no problems with the sensors.. I'm not too sure if the FSM shows the oiler, but I'm pretty sure it does..


Is that the cover I have a picture of in the first post? Because it's slightly damaged and I'm not sure if it can still be used.

Thank you!!


Yes The Same One From The Pic.. if the P11 cover is damaged the only way around it is buying another 99 p11 trans.. reason being that you have A P11 chassis.. unless you could source A 99 P11 cover by itself..
2014-06-25 14:41:44
#15
Originally Posted by 91sentragti-r


a B14 Trans will not be a straight drop in on Your P11... the mounting points for the front transmission mount Is different... however you should be able to use the gear stacks of the 94 on your p11 casingS as you said... as For the OP, Can't really tell what you are talking about... try to snap a better shot...


The 99 P11 transmission has the same mounting as the B13/B14. The '00+ use the top mount like the B15. The only issue would be the '94 transmission won't have the hole for the crank angle sensor in the bellhousing, but that can be added.
2014-06-25 22:42:26
#16
Originally Posted by eric96ser
Originally Posted by 91sentragti-r


a B14 Trans will not be a straight drop in on Your P11... the mounting points for the front transmission mount Is different... however you should be able to use the gear stacks of the 94 on your p11 casingS as you said... as For the OP, Can't really tell what you are talking about... try to snap a better shot...


The 99 P11 transmission has the same mounting as the B13/B14. The '00+ use the top mount like the B15. The only issue would be the '94 transmission won't have the hole for the crank angle sensor in the bellhousing, but that can be added.


are you sure about that?? if I'm not mistaken all P11 Trans use the top trans mount..all p11 transmission indeed have the same mounting points as the B13, but he has A P11 chassis which will require the top mount which the b13 transmission doesn't have the mounting points for.

however the P10 transmission doesn't use the top mount maybe you're getting them mixed up since the 99p 11 is still a 32V box..
2014-06-26 02:20:12
#17
find a new trans....@ least a 99 p11 is a direct swap, since it has provisions for mount configs.

in terms of the outter case....thats where 1 of the shaft bearings sits. Im willing to bet that since that is marred there...the oppsing side is as well. (id remove that & have a look)

a similar thing happened to me with a trans. the inputshaft bearing went completley & thus caused the shaft to have play in it, & the top/case side was also messed up..

i had a buddy fix the motor side, but he couldnt get in the outter case to fix that side, so i got a new outter case
2014-06-26 13:39:52
#18
'99 P11 transmission: http://www.sr20-forum.com/driveline-fs/74208-1999-infiniti-g20t-lsd-tranny-transmission-converted-cable.html
2014-06-26 18:44:23
#19


if you read the description it clearly states that the transmission was in a 94 b13 Not A P11... like I said before you could bolt any p11 transmission on a B13 Or B14, but not a b13 or b14 transmission on A p11... also take a closer look at the picture and you could clearly see the mounting points for the top mount... I'm not trying to give misleading information.. just talking on experience since I rebuild these transmissions all Day...
2014-06-26 18:46:35
#20
also you could go on eBay and find the transmission mount and you will see it does not look like the 3 bolt one from the front cover
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top