Thread: Help ASAP!!! Remove d/s axle!!!

+ Reply To Thread

First

Posts: 11-15 of 15

Search Thread

2012-07-15 19:57:35

#11

92SentraSE-R Online/offline status of 92SentraSE-R is unknown

b14+p11=<3

Join Date: 2010-03-11
Location: 209, CA
Posts: 2,211
Trader Score: 3 (100%)

I went to good ol harbor freight and picked me up a set of punches...

Took the 3/16 and it wouldn't fit staight in due to the bar that goes inbetween there... So I take my hammer and bend it as so

Couple of hard hits and the thing goes flying out!

0 Likes

Be the first to like this post.

Reply Reply With Quote

2012-07-15 20:06:23

#12

tomas527

Member

Join Date: 2008-09-19
Location: PA
Posts: 2,517
Trader Score: 40 (100%)

Congrats..sucks axle is fudged up.

0 Likes

Be the first to like this post.

Reply Reply With Quote

2012-07-16 00:28:33

#13

lynchfourtwenty Online/offline status of lynchfourtwenty is unknown

SR20VE-T Boost Junky!

Join Date: 2008-09-27
Location: Washougal, Washington
Posts: 9,933
Trader Score: 17 (100%)

Originally Posted by Benito
When I did my last swap my mechanic friend used a big pry bar in his left hand and he grabbed the axle and jiggled/roatated it with his right hand (a very well trained hand I might add) at the same time. Took ten seconds I shit you not. I was across the shop and turned around. Before I could say 'don't do that' it was out.

The driver side axle can be a real pita, i've had them come out easy, and had some difficult ones.. but I always prevail! I either use a pickle fork or pry bar and some wiggling an jiggling. Next time ya need one out ben hit me up!

an to the op of this thread, holy shit dude you scratched that case up something bad

oh and the ring that goes around the axle seal too...

Last edited by lynchfourtwenty on 2012-07-16 at 00-29-27.

0 Likes

Be the first to like this post.

My Car Thread http://www.sr20-forum.com/members-rides/15788-lynchs-ve-se-r-project-thread.html
My Turbo Thread http://www.sr20-forum.com/turbo/50178-lynch-s-ve-t-thread.html

Reply Reply With Quote

2012-07-16 00:35:40

#14

Chriscar

ADMINISTRATOR

Join Date: 2007-12-13
Location: Dallas, TX
Posts: 2,240
Trader Score: 19 (100%)

Wish I would have seen this earlier, because it would have saved you allot of time and sweat. All you need to do is wrap a rope or chain around the axle in the space between that cup and the trans, then sit on your ass with your legs parallel to the axle, give the chain a quick sharp tug, and the axle will pop right out.

C

0 Likes

Be the first to like this post.

cogito ergo zoom................
1994 SE-R / [S]DE+GT2560R / S4 / Nismo LSD / Calum Realtime/ 15x7 RPF1[/S] / Hyperco - AGX. Just about stock.
1995 [S]Turbo[/S] Miata R Package / [S]GT2560R[/S] NA is best, Bro / VVT engine /Megasquirt / Flyin Miata suspension / 15x8 949 6UL

Reply Reply With Quote

2012-07-16 03:35:40

#15

92SentraSE-R Online/offline status of 92SentraSE-R is unknown

b14+p11=<3

Join Date: 2010-03-11
Location: 209, CA
Posts: 2,211
Trader Score: 3 (100%)

Originally Posted by Chriscar

lmao this was going to be the next step because I'm at my brothers house so I don't have access to much... I just have my chain holding up the old engine

I'm almost ready to put everything back into the car! just need to swap the header over, put the tranny on and drop the bitch in

0 Likes

Be the first to like this post.

Reply Reply With Quote

First

+ Reply To Thread

Thread Information

There are currently ? users browsing this thread. (? members & ? guests)
StubUserName