Thread: Need A 91 Nx1600 Wiring Diagram To Wire Into A 93 SER Sentra(EDITED 1-16-12)

soon very soon . im saving up for it . the cluster was cheap VERY cheap so i got it

Couple of questions. Have the pigtail and the cluster, Marked all the wires on the pigtail as well.

On my 91 cluster harness

Pin- M102-5 Low fuel

where would I attach this to on the NX pigtail? Pin number 5 (fuel) or pin number 26 (fuel gauge)?

***

Pin 25 (shared ground) on the NX pigtail. I'm guessing I can use this as the ground for batter, temp , high beam, tach , clock, and whatever else needs grounded beside speedo?

***

Since I'm running a mechanical speedo, to transfer over I'm guessing I would just:

Splice b13 M102-6 (speedo) to NX 24 (speedo to ecu)

then just run the wires from the electronic speedo in the trans to NX pin 32 (speedo to cluster) and 34 (speedo ground).

***

The Two wire buzzer..what the hell is this thing and is it even necessary?

********

Thanks for any help that can be provided, these are the only issues I can see. Your diagrams are a bit different than mine so I'm doing this based on fsm pinouts and forum made guides.

Paxton

i did it a few years back, it's pretty simple actually.

It seems simple, just need clarification

Added a few comments

Thanks a bunch man, I just wanted some sort of confirmation that I had it right.

It's just hard to believe that that little box behind the cluster produces such an annoying sound lol



I read this a few times in a few threads =p, I completely understood that haha I found a diagram that seemed to match my exact cluster and went from there. Sinister's diagram more or less just gave me the courage/motivation to try this out...and the free cluster haha

Thanks again MOJO,
Paxton

quick question MOJO,

Ign and acc wires would go where?. M33-27 on the B13 cluster says, yellow - power for pretty much everything...?

This is what I've got so far.


’91-’92 cluster wiring to 91 nx16 cluster

Right side 12 slot symmetrical plug black

CEL M30-35 to 3 check engine
fuel M102-1 to 26 fuel gauge
door open M102-2 to 7 door
washer (canada) M32-10 ....unused
low fuel M102-5 - to 5 fuel
power for fuel gauge, ABS light, seatbelt, brake, oil pressure, temp gauge, speedo, battery. M32-15 to ?
clock backlight M30-38 to 23 constant 12+ for clock
ABS ground M102-7 ...unused
left turn signal power M102-8 to 8 left signal
ground M33-27 to 13 turn signal ground shared and 25 shared ground
Empty slot M33-25

Middle 10 slot, offset plug black

Tach ground (add a ground or use one that’s unused) ? not sure
Black (bottom left) – Ground for speedo only to 34 speedo ground
Ground for high beam indicator M32-12 to 25 shared ground
high beam indicator M32-11 to 6 beam+
tach signal M30-39 to 30 tachometer
clock M30-37 to 23 constant 12+ for clock
speedo M102-6 to 24 speedo to ecu

Left 12 slot, symmetrical plug white

seatbelt ground M32-9 (2-door) to 25 shared ground
oil pressure ground M30-33 to 25 shared ground
bulb check M30-31 to ?
temp signal M30-41 to 27 temp gauge
brake M30-32 to 18 brake w/ diode
overdrive off ground M33-19 ...not used
battery ground M30-36 to 22 chg batter light ??
right turn signal power M33-26 to 14 right signal
illumination M33-21 to 12 and 29 ill -
illumination M30-40 to 33 and 16 ill +
temp ground M102-3 to 25 shared ground

do you have pics of yourself doing this . jus wondering

Do you want to see? All of my materials and the cluster are at the shop, I can take pics Monday.