Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: w10 T25 Turbo elbow bolts

+ Reply To Thread
Posts: 1-6 of 6
2014-02-26 00:00:34
#1
w10 T25 Turbo elbow bolts
Does anyone know where I can find the original bolts for the w10 T25 turbo elbow? If you have to get some at a local hardware shop, what size are they? I know there are 2 long bolts (approx. 3 inches) and 1 (approx. 1 inch). Thank you kind sirs.
2014-02-26 00:29:12
#2
Originally Posted by 96NismoB14
Does anyone know where I can find the original bolts for the w10 T25 turbo elbow? If you have to get some at a local hardware shop, what size are they? I know there are 2 long bolts (approx. 3 inches) and 1 (approx. 1 inch). Thank you kind sirs.


atp turbo sells what you need. You could also get them from ebay. the 5 bolts on the exhaust housing are 8x1.25mm. the 3 on the j-pipe are 10x1.25mm.
2014-02-26 00:40:21
#3
Just go get them from the bolt store. Thats what i always do. I normally swap them after each time I pull the turbo manny and all off. About $5-8 for the bolts around here from the bolt store. Or you can go to Ace hardware and they are even cheaper.
2014-02-26 15:01:44
#4
Originally Posted by cortrim1
Originally Posted by 96NismoB14
Does anyone know where I can find the original bolts for the w10 T25 turbo elbow? If you have to get some at a local hardware shop, what size are they? I know there are 2 long bolts (approx. 3 inches) and 1 (approx. 1 inch). Thank you kind sirs.


atp turbo sells what you need. You could also get them from ebay. the 5 bolts on the exhaust housing are 8x1.25mm. the 3 on the j-pipe are 10x1.25mm.


Appreciate it. Thanks for the info.

- - - Updated - - -

Originally Posted by Johnny
Just go get them from the bolt store. Thats what i always do. I normally swap them after each time I pull the turbo manny and all off. About $5-8 for the bolts around here from the bolt store. Or you can go to Ace hardware and they are even cheaper.


Ill definitely check out Ace Hardware. I just didn't know the size and measures. Appreciate the help.
2014-03-05 01:45:50
#5
I'm not sure if this pertains to all J-pipes but you may find this helpful.

Here's a quote from the thread below on Jpipe stud size:

"I ran into some trouble on the j-pipe studs. I read that the j-pipe studs were the same as used for the manifold (M10x1.25). Sure enough, the 10x1.25 nuts threaded right on."
"It took me forever to figure out what was going on… the original stud was two totally different threads! The “anchor” end was M10x1.5 and the “nut” end was M10x1.25. WTF?! "

http://www.sr20-forum.com/general-maintenance/729-how-replace-manifold-j-pipe-studs.html
2014-03-05 11:14:35
#6
Sounds like he is asking about the t25 comp outlet elbow bolts. They are a standard Nissan 10mm so just get what you need from your local hardware store. Your good to use any grade on the comp side but make sure your using grade 8 or close on the exhaust side or you risk breaking them.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top