Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: Banjo fitting - where to buy?

+ Reply To Thread
Posts: 1-10 of 10
2009-03-01 05:11:06
#1
Banjo fitting - where to buy?
I'm looking for a banjo, 14mm-to- -6AN male fitting. Needs to come with both crush washers and a 14x1.5mm threaded banjo bolt.

I found one at ATP turbo. Earl's, Aeroquip, etc don't seem to make one this size (or any 14mm banjo for that matter).

ATP is in California, I'm in Ohio. Is there anywhere on the East Coast that carries this sort of thing? I'm trying to get it quickly, and if I order from them it'll be most of a week unless I pay out the nose for overnight shipping.
2009-03-01 15:41:04
#2
You don't have a hosepower USA?

Or for that matter, any hot rod performance shops in the area? Most hot rod shops I have been to have like a billion different types of AN fittings.
2009-03-01 15:50:31
#3
Take a look here, Himni-Racing Ive bought a few things off them..Might find what you need plus some. They are located in Fl. so shipping time wouldnt be long.
2009-03-01 15:54:55
#4
Originally Posted by TeKKiE
You don't have a hosepower USA?

Or for that matter, any hot rod performance shops in the area? Most hot rod shops I have been to have like a billion different types of AN fittings.


Yes, we have a hotrod shop. It's after hours there. Also, Summit is only three hours away. However, I was on the phone with a Summit rep last night and he went through the Earl's, Aeroquip, and Holley catalogs, with no luck. The largest banjo they seem to make is only 12mm.

I've never heard of Hosepower USA. We have a business in town called Ohio Hydraulics but they're also only open during normal business hours, so I have to wait till tomorrow to call.

I'm trying to find somewhere to get this relatively quickly; hence the question. You didn't really think I'd ask without research, did you?
2009-03-01 15:57:18
#5
Nismo, I checked on Himni's website, they've got one that goes to a hose barb and a couple that go to pipe thread fittings, but no 14mm banjo to the -6AN fitting I'm trying to find. I appreciate the head's up, I can probably make this work with a hose barb if I have to but I'd rather do it with the AN setup.
2009-03-01 16:02:08
#6
Originally Posted by Rittmeister
Nismo, I checked on Himni's website, they've got one that goes to a hose barb and a couple that go to pipe thread fittings, but no 14mm banjo to the -6AN fitting I'm trying to find. I appreciate the head's up, I can probably make this work with a hose barb if I have to but I'd rather do it with the AN setup.


Give them a call, they might have what you need just not listed..I gotta look threw and see were else I bought my fittings from..I got a few sites, once I find it Ill let you know.
2009-03-01 16:10:37
#7
I went to eBay for my banjo bolts.

They have 14mm x 1.5 to -AN 4. Link

I remember GoFastDepot had something similar that might work for you if you're making your own -AN 6 lines. Link

I couldn't find exactly what you're looking for though. You say ATP Turbo has it? Sounds to me like you just need to order from them and deal with the wait.
2009-03-01 16:22:43
#8
Originally Posted by Rittmeister
Yes, we have a hotrod shop. It's after hours there. Also, Summit is only three hours away. However, I was on the phone with a Summit rep last night and he went through the Earl's, Aeroquip, and Holley catalogs, with no luck. The largest banjo they seem to make is only 12mm.

I've never heard of Hosepower USA. We have a business in town called Ohio Hydraulics but they're also only open during normal business hours, so I have to wait till tomorrow to call.

I'm trying to find somewhere to get this relatively quickly; hence the question. You didn't really think I'd ask without research, did you?


Wasn't trying to insult your search intelligence. Was just a simple question. Sometimes people overlook the obvious first.
2009-03-01 18:43:23
#9
I found a few places that sell them however they are not close by to you. You could do a 14mm to 1/4npt banjo, and then a 1/4npt to 6an adapter. But I dont know if you have space restrictions or not but Im guessing you do since you are using a banjo.
2009-03-04 04:25:19
#10
Ended up ordering from ATP. GoFastDepot said they'd be happy to sell me a single banjo (the kit is 2) but they had none in stock and no ETA on more

Apparently this is not a common fitting. Next time I'll hope there's more room where I'm working...
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top