Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: The Ultimate 6 Speed Swap Thread...Parts/Instructions/Results!!

+ Reply To Thread
Posts: 471-480 of 485
2016-04-21 03:34:19
#471
Guys i did mine yesterday i took my two specv axles and took them to a machine shop were they took out the specv outer cv joint and modify the 27 spindles to 25 so i could use normal b13 cjoint on specv axles and i could keep mine hubs and brakes ..i did try to search for some hybrid axles like coohee did but i had no luck ..i have a p12 20v swap on a b13 engine and tranny 20v

Sent from my SM-N920P using Tapatalk
2016-05-08 21:09:40
#472
Sooo, I've got an interesting issue:



I wasn't getting any speed reading on my cluster since I did the swap. I followed the guide,
You need to cut off the tab for the securing bolt as the sensor needs to be rotated clockwise more from its normal location to seat right in the trans. Be careful when installing, one all the way down rotate it until you feel it hit up against something and that should be good. I used the normal bolt with a wide washer to secure mine and had no issues and the speedometer worked like a charm.
But it obviously didn't work... I wish I had bench tested it before throwing it on the car. I could swear that it felt right installing it though.

Any ideas besides throwing a new one in? I'm just worried that the internal gear ring has taken some damage...
2016-05-08 21:24:22
#473
GPS speedo?

Certainly would suck if the gear on the diff was damaged.
2016-05-11 23:03:43
#474
Any of you guys getting pretty annoying squeaking while idling/driving and clutch not pressed in? Slightly pressing the clutch makes it stop. Not sure if it's the slave vibrating against the fork or the TOB it self. I just added some axle grease between the slave and the fork, but doesn't seem like that helped.

Also getting a different squeak when pressing the clutch in, not quite sure what to lubricate...
2016-05-12 01:51:13
#475
Originally Posted by Vadim
Any of you guys getting pretty annoying squeaking while idling/driving and clutch not pressed in? Slightly pressing the clutch makes it stop. Not sure if it's the slave vibrating against the fork or the TOB it self. I just added some axle grease between the slave and the fork, but doesn't seem like that helped.

Also getting a different squeak when pressing the clutch in, not quite sure what to lubricate...


whats brand TOB?
2016-05-12 02:48:10
#476
I'm pretty sure OEM, since they don't sell the little clips on their own, I remember paying $60ish for new TOB from the dealer.
2016-05-16 13:52:49
#477
I started the car, unbolted the slave cylinder and the noise was gone. Pushing or pulling on the TOB arm didn't make any noise, thus it's not the throwout bearing. I think it's just slave metal hitting the arm metal and squeaking, though Im surprised grease didn't stop it then. I think I'm gonna put some rubber between them and see if that helps.

The squeak when I press the clutch in is more like a crunchy one and only happens when it's cold, probably the TOB just dragging against the input shaft.

EDIT: Took the piston rod out of the slave added grease behind it figured it might be rubbing back there, but still squeaked. Tried to fit one of those rubber hose nipples but they were too long. Took some nitrate glove fingers and put them on the slave's rod that touches the fork, and bam squeak is gone. I wonder why mine is making noise while others are fine...
Last edited by Vadim on 2016-05-16 at 18-56-34.
2016-05-31 13:55:31
#478
This Saturday I got fed up with the squeaking while idling and started tearing down the slave cylinder yet again to add rubber someplace else since the gloves didn't last . I unbolted the slave and was trying to clean out the synthetic axle grease. Cleaned old grease out, that I added a few weeks ago, pressed the clutch with my hand slightly to get wipe more of the old grease out, then added some sil-glyde to the part where the piston rod sits.

When I went back to assemble it I couldn't get it in the fork and get the bolts to align, which was surprising, I used a screw driver to push the top to get the slave aligned with the transmission and finally got the bolts in. Started the car and no squeaking! The piston rod was now pretty tightly pressed against the fork thus had no place to vibrate. I am a little worried about clutch preload with this. Now here's the kicker, went to drive the car and stalled it, the clutch engagement point moved WAY up, it releases much higher then before, more typical of a hydro clutch, where before it was like a stretched cable clutch.

Either the new grease helped or pressing the clutch in by hand while it was removed realigned the piston and now it's 100% times better.
Last edited by Vadim on 2016-05-31 at 13-59-12.
2016-11-16 16:45:24
#479
Originally Posted by ashtonsser
Now there is also another little secret you can do to help shorten the axles for those that have binding issues as well. A honda guy gave me this idea recently. You can take the actual joint that attaches to the midshaft, pound it further down the axle and cut a new groove for the c-clip. The guys that had binding issues really only need about 1/2" more of cv play. Doing this can give you almost 3/4" So for those using full on b15 axles and hub setups and dont want binding issues mainly caused by the driver side axle, give that a shot, dissasemble the axle and pound the joint at the inner cv down further onto the shaft and make your own new groove for a c'clip


Ashton....Do I need to look into doing this?
2016-11-24 09:46:50
#480
TDMI sells a hub that fits the stock knuckle and lets you use the spec v axles.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top