Thread: How to: RS6 6 speed swap guide

+ Reply To Thread

First

Last

Posts: 131-140 of 285

Search Thread

2012-11-25 00:07:45

#131

ashtonsser Online/offline status of ashtonsser is unknown

SR20VETeran

Join Date: 2007-12-11
Location: Copperas Cove, Tx
Posts: 9,349
Trader Score: 13 (100%)

No there is no issues with it. Matter fact if its a street car I highly recommend welding them together.

0 Likes

Be the first to like this post.

1992 Nissan Sentra SE-R - Fully Built SR20VE, BWS400SX Billet 67mm and much more
JMS Racing tuned to 716whp, 423wtq at 29psi
10.5 @ 149.2mph to date I believe the fastest trap speed SE-R, Much more to come with some changes!

Reply Reply With Quote

2012-11-25 05:20:24

#132

boostednx

additcted to boost

Join Date: 2007-12-16
Location: the river
Posts: 1,430
Trader Score: 3 (100%)

Has anybody tried to use a gtir clutch master cylinder ?

0 Likes

Be the first to like this post.

SR20DEEP,MARSH TUNING
94 Se-r vq35 daily
94 ser 67mm turbo car

Reply Reply With Quote

2012-11-25 05:22:06

#133

SE-Rawkus

Est. 2003 - Grade A Beef

Join Date: 2007-12-12
Location: Miami, FL
Posts: 1,343
Trader Score: 27 (100%)

Originally Posted by boostednx

Has anybody tried to use a gtir clutch master cylinder ?

From what I hear, you can use it with no issues.

0 Likes

Be the first to like this post.

Manny
Unretirement phase 2...
Manny's '95 Bfourteen
SR20DEEP

Reply Reply With Quote

2012-11-25 05:23:47

#134

boostednx

additcted to boost

Join Date: 2007-12-16
Location: the river
Posts: 1,430
Trader Score: 3 (100%)

Originally Posted by SE-Rawkus

Originally Posted by boostednx
Has anybody tried to use a gtir clutch master cylinder ?

From what I hear, you can use it with no issues.

From what I seen online it looks like a direct bolt in item and can be easily had.

0 Likes

Be the first to like this post.

SR20DEEP,MARSH TUNING
94 Se-r vq35 daily
94 ser 67mm turbo car

Reply Reply With Quote

2012-11-25 05:48:33

#135

unijabnx2000 Online/offline status of unijabnx2000 is unknown

This will not end well

Join Date: 2008-01-01
Location: NC
Posts: 5,447
Trader Score: 18 (100%)

i thought mazworx had plenty...?

0 Likes

Be the first to like this post.

1992 NX2000 - GTX28 - RS6
Coming soon - Hardtop NX2000 - Roller rocker

Reply Reply With Quote

2012-11-25 16:04:18

#136

tswii

Member

Join Date: 2010-11-17
Location: Northeast Florida
Posts: 947
Trader Score: 11 (100%)

I got my slave and bellhousing from Greg at Gspec. He was $55 cheaper on the bell than mazworx. They told me the P12 stuff was on backorder and didn't know when they could get it, but Greg got it to me in a week. They do have the conversion mount kits though.

0 Likes

Be the first to like this post.

Reply Reply With Quote

2012-11-27 19:01:48

#137

unijabnx2000 Online/offline status of unijabnx2000 is unknown

This will not end well

Join Date: 2008-01-01
Location: NC
Posts: 5,447
Trader Score: 18 (100%)

Originally Posted by ashtonsser

Alright people. Looks like the hubs are able to be drilled and resplined for the b15 axles without a problem. Cost should be around 100 bucks for a pair of hubs that you send in to have done.

If you need them done, contact Frank at DSS. He has all the information you need.

Just talked to Tad. My hubs will be ready at the end of the week.

0 Likes

Be the first to like this post.

1992 NX2000 - GTX28 - RS6
Coming soon - Hardtop NX2000 - Roller rocker

Reply Reply With Quote

2012-11-27 19:48:15

#138

Turbo91SER Online/offline status of Turbo91SER is unknown

Addicted to SR20's

Join Date: 2007-12-11
Location: Corpus Christi, Tejas
Posts: 1,643
Trader Score: 35 (100%)

Originally Posted by ashtonsser

So, these are the B13 CV on the hub end so you don't have to swap hubs? You have these redone and then installed on your B15 tranny side CV and shaft?

0 Likes

Be the first to like this post.

'92 SE-R Undergoing a transformation - '05 NISMO Frontier 4WD CC - '08 M35 - '00 P11 DD - The Boomerang

Reply Reply With Quote

2012-11-27 20:02:39

#139

unijabnx2000 Online/offline status of unijabnx2000 is unknown

This will not end well

Join Date: 2008-01-01
Location: NC
Posts: 5,447
Trader Score: 18 (100%)

The B13 hubs are being splined bigger to fit spec-v axles.

0 Likes

Be the first to like this post.