Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: bumpsteer kit

+ Reply To Thread
Posts: 111-120 of 166
2010-08-12 15:06:46
#111
Octotat: Are these still available?
Could this kit be combined with the control arm prototypes and shipped in one box?

(what is the estimate for shipping both kits to NY 14303).

Thanks.
2010-09-03 18:57:20
#112
Does anybody knows if these are still available? I have been unable to connect with Chuck.

Thanks.
2010-09-06 19:22:27
#113
x2 I'm interested.
2010-09-14 05:36:55
#114
i have 3 kits available

thanks
-chuck
2010-10-11 16:01:57
#115
Chuck, how can I get in touch with you, it's regarding the control arms and bumpsteer correction kits. PM me your phone number.

Thanks,
Wojtek
2010-10-21 20:43:20
#116
PM sent,
Chuck you are super hard to get in touch with.
2010-10-26 06:48:30
#117
Has anyone had fitment issues with this kit? I just had a mate try to fit one to his NX and he's had issues with the heim joint ID being too small to fit over the shaft, awaiting confirmation from him after checking the threading of the nuts to the studs he said one nut stripped out (looks like wrong thread possibly? because they weren't torqued down). Also the tie rod cannot be threaded into the adapter enough to give a sufficient wheel alignment (has got heaps of toe in).

Any feedback from people who have fitted the kit? I haven't attempted fitment of mine yet so this information is only being relayed as my mate is in another state. I just expected more of a straight forward fitment.
2010-11-10 16:53:26
#118
Originally Posted by Cozzm0_AU
Has anyone had fitment issues with this kit? I just had a mate try to fit one to his NX and he's had issues with the heim joint ID being too small to fit over the shaft, awaiting confirmation from him after checking the threading of the nuts to the studs he said one nut stripped out (looks like wrong thread possibly? because they weren't torqued down). Also the tie rod cannot be threaded into the adapter enough to give a sufficient wheel alignment (has got heaps of toe in).

Any feedback from people who have fitted the kit? I haven't attempted fitment of mine yet so this information is only being relayed as my mate is in another state. I just expected more of a straight forward fitment.


What car was this on b13 or b14?
2010-11-10 17:07:16
#119
Originally Posted by Cozzm0_AU
Has anyone had fitment issues with this kit? I just had a mate try to fit one to his NX and he's had issues with the heim joint ID being too small to fit over the shaft, awaiting confirmation from him after checking the threading of the nuts to the studs he said one nut stripped out (looks like wrong thread possibly? because they weren't torqued down). Also the tie rod cannot be threaded into the adapter enough to give a sufficient wheel alignment (has got heaps of toe in).

Any feedback from people who have fitted the kit? I haven't attempted fitment of mine yet so this information is only being relayed as my mate is in another state. I just expected more of a straight forward fitment.


I cannot provide feedback regarding the new studs and the heim fitment but I can tell you that I had to cut the heim joints (threaded end) down so that they did not bottom on the in er tie rod (inside the coupler). I only had to cut one side but I wound up cutting both to give myself the flexibility.
2010-11-10 17:22:37
#120
Originally Posted by Cozzm0_AU
Has anyone had fitment issues with this kit? I just had a mate try to fit one to his NX and he's had issues with the heim joint ID being too small to fit over the shaft, awaiting confirmation from him after checking the threading of the nuts to the studs he said one nut stripped out (looks like wrong thread possibly? because they weren't torqued down). Also the tie rod cannot be threaded into the adapter enough to give a sufficient wheel alignment (has got heaps of toe in).

Any feedback from people who have fitted the kit? I haven't attempted fitment of mine yet so this information is only being relayed as my mate is in another state. I just expected more of a straight forward fitment.


We has this issue. The inner tie rods were too long to provide sufficient adjustment of the toe, resulting in toe-in. That was with the outers mounting onto the bottom of the spindle. We ended up just mounting them on the top, like stock. I guess a fix for this in our case would be to get shorter inner tie rods?
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top