Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: What Did You Do To Your B14 Today?

+ Reply To Thread
Posts: 2,211-2,220 of 2,656
2012-09-24 15:40:46
#2211
Originally Posted by eggman
Originally Posted by Wayne
Where did you get the bar from? Is that on a b14?


Seriously Wayne? ...dude read the post,it says where he got it and how much....and its obviously a B14


The bar is on a B14. My exhaust is 2 1/2", but they have done it on a car with a 3" as well.
The $100 cost I listed is for bending the beam to zero toe. The bar installation was around $700, and well worth it.
Zero toe, which I had done a few years ago, is a noticeable improvement, even on the street. The Panhard bar is slightly noticeable on the street, but really shows up big time on the track. I could pretty much set the car up in a corner with the brakes and then steer with the throttle at the limit of my tires.
IMHO, the money spent on these mods improves handling much better than a decent set of coil overs. (I run AGX and Hyperco springs).
2012-09-24 18:32:59
#2212
Got the B14 tuned with the N1's at the Final Speed Garage open house / SR20DEEP BBQ bash yesterday. Made a huge difference....now just need a better clutch!



Last edited by SER96VSPEC on 2012-09-24 at 18-50-29.
2012-09-24 18:53:03
#2213
Originally Posted by SER96VSPEC
Got the B14 tuned with the N1's at the Final Speed Garage open house / SR20DEEP BBQ bash yesterday. Made a huge difference....now just need a better clutch!





I went for test ride in it right after the tuning and this fkn car pulls like a raped ape!! makes me wanna get N1's asap!!
2012-09-28 01:56:11
#2214
N1's and supertach valve springs FTW!!
2012-09-28 19:38:38
#2215
Originally Posted by ivanorcan
Today I instaled my new front brakes!!

They look awesome, at this moment the braking power is not good but should get better with the days. It came with Hawk "street" pads... i really dont know which kind...



OK, regarding this, 2 days ago i noticed that one of the calipers was bleeding brake fluid from the screw that goes to the brake line, i took it to the brake shop and they changed the screw and done... now it brakes awesome!!!
2012-09-29 04:34:11
#2216
My friggin driver's side door handle broke off today! Anyone know if this is the correct part?

HANDLE ASSY-FRONT DOOR OUTSIDE,LH - Sentra / 200SX (B14U) 08/1997-10/199 :: Nissan Parts, NISMO and Nissan Accessories - Courtesyparts.com
2012-10-01 13:21:11
#2217
I installed a new exhaust in my car, 3 inch crush bent exhaust, with a glasspack and a Dynomax Ultra Flow. The car now have more low end torque and pulls harder on top.

2012-10-13 17:07:33
#2218
F U Front Anti-Sway Bar!


Disconnected the front anti-sway bar end link with a little persuasion and swearing. I think I can re-sell it for future use...
2012-10-14 06:32:25
#2219
Installed HID's and painted some new rims I got.

Before

After


New HID's
2012-10-14 06:50:32
#2220
Looks like a lil bit of scatter for those hid's, do you have the bulb housings? or did you just throw hid's in stock lights?
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top