Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: N60 MAF wiring assistance please (I'm colorblind)

+ Reply To Thread
Posts: 21-30 of 32
2014-04-16 04:03:22
#21
Okay thanks. I'll mess with the voltage meter tomorrow, supposed to be 50 and sunny. The motor idles but real crappy and low, and then stalls usually after 30 seconds. I'll try it tomorrow if it's not SNOWING (yes I'm serious). It was 84 degrees on Sunday, 74 yesterday.. and now snowing tonight after heavy rain in SE PA
Last edited by Storm88000 on 2014-04-16 at 09-03-01.
2014-04-16 13:07:58
#22
Originally Posted by Storm88000
Originally Posted by Chriscar
Use a volt meter and this PDF - http://jimwolftechnology.com/wolfpdf/maf%20Z32%20CONVERT%20TO%20OTHER%20NISSANS.PDF

The image is from the HARNESS side, not the pin side.

C


That is the Z32 MAF correct? I see in the diagram there are 6 wires, mine is 5.
Yes, but the plug configuration and wiring are the same. Notice that the two outside wires (A & F) are not used.

C
2014-04-16 18:00:11
#23
Maf harness | B13 harness

White/black stripe -> Orange/ blue stripe (12v)
Both black -> White (ground)
White -> Orange (5v)

Very simple.
2014-04-16 22:06:23
#24
Originally Posted by SR20GTi-R
Maf harness | B13 harness

White/black stripe -> Orange/ blue stripe (12v)
Both black -> White (ground)
White -> Orange (5v)

Very simple.



It would seem to be, but when you can't see most colors especially when they're small wires it's not.

So today I went to a pull yard and got a whole bunch of N60 MAFs w/ pigtails - just in case my current one is dead. I think I hit every 89-94 Maxima in the place, and whats funny is right while I was pulling out a tow truck was bringing another 89-94 Maxima into the salvage yard. If mine is ok, then well then there will be a few N60's in the classifieds:
.


(pic from just now)
2014-04-16 22:13:07
#25
And that's why you need a DVM. Disconnect the MAF plug, turn the key on, and find the power and ground wires. The one that's left is for signal.

C
2014-04-16 22:28:02
#26
thanks I have them hooked up according to SR20GTi-R - im gonna try to start it up with a new MAF in a bit
2014-04-16 23:34:42
#27
............................and we have LIFT OFF!!!!!!!!!!! Old MAF must have been done. Car started right up and idles/drives fine. now I have 4 N60 maf's. lol
2014-04-17 07:12:25
#28
i figured.. lol

now finish breakin in that clutch!
2014-04-17 22:07:19
#29
Originally Posted by lynchfourtwenty
i figured.. lol

now finish breakin in that clutch!


I now have 2 extra N60's MAF's (both work, I just tested them out) - I just want what I paid for them $35 each + shipping check the classifieds if anyone here needs one
2014-04-17 22:18:03
#30
Edit here's the thread: http://www.sr20-forum.com/naturally-aspirated/73418-two-n60-mafs-w-pigtails-wiring-harness-40-shipped-each.html#post973857
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top