Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: Well Check This VE Header I found On EBAY

+ Reply To Thread
Posts: 21-30 of 30
2013-06-25 07:01:19
#21
I don't wanna advertise without the right vendor status or initiating a group buy, but here is our civic, it shows some of our fabbing skills. I think the only problem would be to actually have people commit to buying. Only test header I will have that I can compare to is an SSAC, unless I can somehow get @Teal97 down here to do some comparisons.

http://www.sr20-forum.com/general-non-sr20-discussion/66393-race-car-eg-k24-k20.html
Last edited by sentraman on 2013-06-25 at 07-02-51.
2013-06-25 12:09:19
#22
Originally Posted by sentraman
I don't wanna advertise without the right vendor status or initiating a group buy, but here is our civic, it shows some of our fabbing skills. I think the only problem would be to actually have people commit to buying. Only test header I will have that I can compare to is an SSAC, unless I can somehow get @Teal97 down here to do some comparisons.

http://www.sr20-forum.com/general-non-sr20-discussion/66393-race-car-eg-k24-k20.html

well get one started and the following will come. People want a following but if one is made and tried and tested people will follow and buy a backed product, yes people are cheap but they will also pay for a quality product.
2013-06-26 15:08:48
#23
I will vouch for their quality fabrication work. I had exhaust work done by them on my Celica Alltrac, and it was top notch!
2013-06-26 16:31:01
#24
They also sell this one for 650,


Any thoughts?
2013-06-26 18:27:45
#25
Originally Posted by Nicoxis
They also sell this one for 650,


Any thoughts?


That one actually look like it should work good. Length of the runners looks long enough than the one posted above to be a good header. Any more pics and info on it?
Last edited by 1sentra-se-r on 2013-06-26 at 18-29-11.
2013-06-26 21:37:37
#26
from his facebook comments on the longer header...

"od primary tubes 1 3/4, outlet on collector 2 1/2, length each tube 24 inch.+ - 1/4. 100% stainless steel t -304 and tig welded. total price $700 usd.''

i think air conditioning would be a casualty with this header. would of been nice to see 12 inches of 1 7/8 after the first 12 inches of 1 3/4. it would be nice to also see a photo of it installed.
2013-06-27 02:39:49
#27
It would be cooler without the fake Nismo logo.
2013-06-28 00:41:28
#28
Thats not a bad looking header, has there been any results on it so far as in dyno improvements?

Thanks @sentraman for getting us started on the future of a VE header.
2013-06-30 05:24:02
#29
Originally Posted by sentraman
How much interest is there really now for a VE header? Not to jack the thread, but if there was enough dedicated folks to actually buy them I could talk to my fab shop and talk about making one. It would be fabbed and tested in house. We do have a dyno in our facility as well as a VE swapped B13.


Please make one. I too am looking to go VVL but can justify spending $700 on a header, nor do I want to go Ebay cheap. I think a decently priced VVL specific header would do very well here.
2013-07-03 02:00:05
#30
Building one for under $700 is going to be a little it hard, considering how much everyone wants from a nice header. We will try our best to work out the best pricing.

Originally Posted by CleanSER
Originally Posted by sentraman
How much interest is there really now for a VE header? Not to jack the thread, but if there was enough dedicated folks to actually buy them I could talk to my fab shop and talk about making one. It would be fabbed and tested in house. We do have a dyno in our facility as well as a VE swapped B13.


Please make one. I too am looking to go VVL but can justify spending $700 on a header, nor do I want to go Ebay cheap. I think a decently priced VVL specific header would do very well here.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top