Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Payu's Mentions Received

All posts where Payu has been mentioned by other members.

Payu's Mentions Received
- All posts where Payu has been mentioned by other members.
Posts: 1-20 of 20
Thread Title / Post Title / Post Preview
Posted By / Posted At
Forum Section
Thread: any info on this car?
Post: El cenizo oh yeah, Payu
El cenizo oh yeah, Payu
2016-01-04 20:28
Thread: Ebay TriY header review/results thread
Post: Thanks...the full writeup and videos are not finished or ...
Thanks...the full writeup and videos are not finished or uploaded yet...stay tuned!

Thats the basics...a full writeup is still in the works so check back...but it sounds like you may be giving so...
2015-03-25 00:12
Thread: How much boost with stock sleeve with 88mm bore will hold!!
Post: Going for 35+psi? Payu May want to go with a slightly ...
Going for 35+psi? Payu

May want to go with a slightly bigger turbo.
2015-03-13 13:28
Thread: Intake manifold options
Post: nmd
nmd
2014-10-29 11:33
Thread: Intake manifold options
Post: [URL="http://i1334.photobucket.com/albums/w660/sss4me/cpc...
[URL="http://i1334.photobucket.com/albums/w660/sss4me/cpc_zps44b48496.jpg"]http://i1334.photobucket.com/albums/w660/sss4me/cpc_zps44b48496.jpg[/URL]

Payu

"We need some runners like these
So...
2014-10-29 11:31
Thread: Sr20ve dyno
Post: I exchanged pm's with Payu before we hit the Dyno to mak...
I exchanged pm's with Payu before we hit the Dyno to make sure we were set on the setup,Thanks Payu
2014-10-21 03:34
Thread: Intake manifold options
Post: I too tested an excessive with a q45,12" or so intake pip...
I too tested an excessive with a q45,12" or so intake pipe and then lengthed it about 18" additional and gained 10whp without tuning yet. Payu is right.
2014-09-05 00:54
Thread: El pawder 2.2l
Post: Payu, thanks Payu, that car seems to take off quicker? Th...
Payu, thanks Payu, that car seems to take off quicker? The driver is 100%. That team is no joke.
2014-03-11 14:38
Thread: Trackforged Tri-Y header completed!!!
Post: Payu this was a base back to back. There was no tuning in...
Payu this was a base back to back. There was no tuning involved, no changes in any maps, or such. Simple uninstall the SSAC and install our header. When I mentioned tuned, is because we are install...
2014-02-26 15:41
Thread: What else should i do?
Post: jagy Payu where can i get CS cam gears? would the JWT cam...
jagy Payu where can i get CS cam gears? would the JWT cam gears work good?

I just saw Jagy's threat and i want cam gears!! :bigthumbup:
2013-11-28 22:34
Thread: 88mm on a budget!! (Not on budget anymore!!!) New Dyno!!
Post: Can these runs be in SAE correction factor rather than ST...
Can these runs be in SAE correction factor rather than STD, please Payu?
2013-10-04 19:36
2013-09-12 03:12
Thread: looking for some exhaust advice (not another 2.5 vs 3 inch question lol)
Post: Just basically fallow like if you going to build a Tri-Y ...
Just basically fallow like if you going to build a Tri-Y header longer primaries and 2.25 choke..bud search for the Tri-Y header...this is what almost every one from PR are running making good numb...
2013-09-08 05:09
2013-09-07 20:09
Thread: re:sr20ve tuning - opinions
Post: re:sr20ve tuning - opinions
re:sr20ve tuning - opinions
2013-08-25 12:06
2013-08-06 16:32
Thread: SR Individual Throttle Body Design and Theory (ITB)
Post: Payu Please PLEase PLEASe PLEASE read this, it will only ...
Payu Please PLEase PLEASe PLEASE read this, it will only take a couple of minutes
Revenge of the Nerd- Boycott Fakes!
2012-10-30 01:24
Thread: SR22VET SR16VE N1 cams problem
Post: I would say u might have to reshim ur head if the keep po...
I would say u might have to reshim ur head if the keep popping off. Now is it usually the same one that keeps popping of or different ones. Also Payu might be able to give u some hints on cam timing
2012-09-27 10:55
Thread: SR20VE build with 16VE pistons
Post: Thanks, I think I'm going to give them a try, I'm not get...
Thanks, I think I'm going to give them a try, I'm not getting much power after 7000 rpms with the SR20VE ones
2012-07-25 22:18
Thread: SR20VE build with 16VE pistons
Post: A forum memeber was just talking about these cams the oth...
A forum memeber was just talking about these cams the other day, with regards to a similar setup.

Here are two posts by forum memer Payu: [url= URL=http://www.sr20-forum.com/vvl/59845-high-comp...
2012-07-25 20:07
Icon Legend and Forum Information
Contains unread posts
Contains no unread posts
Thread is closed
You have posted in this thread
Users Browsing this Forum
There are currently ? users browsing this forum. (? members & ? guests)
StubUserName

Back to top