All posts where JKTUNING has mentioned other members
Dala - The NEMU1 firmware is not compatible with the flex input on the ADC v2 box right now.
We are actually working on a firmware update for both the V1 and V2 NEMU boards to better support the...
If you can email me a step by step of how to repro this I will check it out!
I am not sure I follow exactly what is going on here.
I have a version ready for testing before release, if you guys would be able to test this on your vehicle to ensure functionality that would be awesome.
This should completely fix the issues you g...
I have a version ready for testing before release, if you guys would be able to test this on your vehicle to ensure functionality that would be awesome.
This should completely fix the issues you g...
I have a version ready for testing before release, if you guys would be able to test this on your vehicle to ensure functionality that would be awesome.
This should completely fix the issues you g...
Noted. The AFR offset should really never be any more than 1 AFR off in either direction.. optimally it should be under +/- .5.
This is definitely either a ECU ground offset issue or the wrong c...
Yes, that is correct. You would only need the v2 adc box and the firmware upgrade (when it is available).
The only real reason to upgrade to the V2 board would be for the accelerometer data ...
That's actually a good question.
You might need to shoot [email]info@hrtuning.com[/email] and email to ask them how they have those outputs setup.
VxROxV - Can you shoot me over another email or PM on here with your order number?
I just went through and cleared out and checked my pending orders and I only see a couple there for base chips....
Are the outputs active in the data screen? Do they ever turn on?
Can you send me your tune file via email? [email]john@j-k-tuning.com[/email]
I REALLY find it hard to believe it would be a software issue, but hey I have been wrong before. You simply need to make sure that you are uploading the basecode when you open a new file and hit co...
Like D-Unit121 has mentioned you can use a generic output to switch to a alternate or secondary map to pull the additional timing and/or fuel corrections that are needed for the second stage.
I ...
You can adjust the knock sensitivity and levels through out the RPM range.
The knock sensor thresholds are completely definable per cylinder and can be used through the entire RPM range if you w...
Yes, it will be shipped USPS priority mail or however he wants to get it there.
I was under the assumption that his event was second weekend in October? I am hoping this gets to you guys in time...
The harness for his car should be done and shipped by Monday if you guys can hold on a few more days.
Just got word about this today!
You would have control over it with the SA version, but with the older stuff it is hard coded and you won't be able to change it.
The max RPM for sure cut is likely 6300 or 6400 RPM, which isn't...
Black to ECU ground.
Blue to where ever you want to wire it into (ADC or MAF input wire)
Red to 5v source (either breakout box OR TPS 5v) - I suggest wiring it all through the ADC breakout box (w...
This is going out today for the raffle!
I hope to make it this year, but I am still not 100% sure.
http://www.j-k-tuning.com/NismoTronic/NismoSA%20Raffle.jpg
OnTheChip marksr20
This is going out today for the raffle!
I hope to make it this year, but I am still not 100% sure.
http://www.j-k-tuning.com/NismoTronic/NismoSA%20Raffle.jpg
OnTheChip marksr20
You can't run the VVL from the ADC box .. the ADC box is for inputs only.
Pretty much any laptop that is capable of running Windows XP and up should be able to run the program with no real issue...
unijabnx2000 - You are welcome to shoot me over your calibration and logs and I can see if I can lend a hand.
The closest air port is Harrisburg Airport .. and I am almost 100% certain AA does offer flights out of there.
The next closest would be Baltimore, BWI.
We will likely record the sessions, bu...
BenFenner - We have had these features released for well over a year now.
The old RT version which was the first one had a limited set of features, but that product is no longer offered.
If you g...
Jybfan04 In your case you would have to wire it to the ADC box, since you are still using the MAF sensor.
Wire the 5v source to the TPS's 5v power source, the ground to the ECU ground and the MAP ...
I will try to work on a better explanation of the decel and accel tables in the help. The dTPS trim you see is the TOTAL accel fuel due to change in throttle.
You have a base table, and then "fa...