All posts where Storm88000 has mentioned other members
That's the way it's supposed to be! And the smokers furiously chain smoke cigarettes while pacing back and forth next to the car when we run into issues
so speedricer told me that when installing a B15 trans in a B13/B14 you need to use the P11 shift linkage and grind it down - however this car came with the B15 trans already installed when I bough...
Need help with clutch install: shifter is wrong position ?
Hell, I've seen 91 SE-R with stock cams, and I think only an intake put down more WHP with the air conditioning on ( SE-RMonkey did this just to see the difference)
Whats it look like under the ...
morgans432 - or anyone who explain this to me - this makes no sense:
I noticed the coolant leaking Thursday last week. It leaked about 1/2 jug of distilled water a day of normal driving (luckily i...
morgans432 - is it really necessary to remove the intake manifold or hoist the motor up to swap these out?
These things look like a huge pain in the ass, from under the car and above. I ordered ...
I PM'ed Kyle privately to clear some things up as to not add more BS to this thread as it's already filled up to the brim.
I will not be posting on this forum much anymore, as long as my name...
Kyle dude I didn't even know you were at the convention til someone said something Sunday at the picnic. I wasn't talking about you. And you are right no one asked me to plug it in the magazine, I ...
OK, here we go. I'm going to respond to your post piece by piece. Even though I had a show until 1am and have to be up in a few hours, I still took the time to do this. Because I believe I have b...
OK, since I was unfairly, and without any warning added to this "buyer beware" list yesterday, I'd like to tell you all why I disagree. I don't know who the OP is, but obviously he doesn't know th...
OK, since I was unfairly, and without any warning added to this "buyer beware" list yesterday, I'd like to tell you all why I disagree. I don't know who the OP is, but obviously he doesn't know th...
On the way to the convention, stopping for some goodies:
http://img.photobucket.com/albums/v87/Storm88000/Storm88000150/cleanwal_zpsunkqlua4.jpg
.
http://img.photobucket.com/albums/v87/Storm88000/...
On the way to the convention, stopping for some goodies:
http://img.photobucket.com/albums/v87/Storm88000/Storm88000150/cleanwal_zpsunkqlua4.jpg
.
http://img.photobucket.com/albums/v87/Storm88000/...
On the way to the convention, stopping for some goodies:
http://img.photobucket.com/albums/v87/Storm88000/Storm88000150/cleanwal_zpsunkqlua4.jpg
.
http://img.photobucket.com/albums/v87/Storm88000/...
On the way to the convention, stopping for some goodies:
http://img.photobucket.com/albums/v87/Storm88000/Storm88000150/cleanwal_zpsunkqlua4.jpg
.
http://img.photobucket.com/albums/v87/Storm88000/...
Its all good. Todd ( SE-RMonkey ) posted the weed thing as joke.
https://cdn.meme.am/instances/500x/28333706.jpg
Stock as in stock internals, stock cams and stock valve springs? I'd have to say you are quite brave if you consistently go over like 7800~ish RPM. Shifting at 8500RPM is built SR20VE territory an...
Totally agree with Chriscar as far as the gobs of useable torque you get with boost. My VE dyno numbers were usually around 200-210whp but torque was only in the mid-upper 140s. I think highest dy...
This is true. By far the most abundant SR20 powered car at the pull yards is the G20. SE-RMonkey and I went to the largest pull yard on the east coast a couple months ago, not one single B13 or B1...
Bushing is in! Had to dremel and drill the hell out of the cabin bolts. Then grind down the lip of the new one as Kyle said. Took like an hour. Nice notchier feel in the shifts now
Awesome. I will let you know in case the shop appointment on Sunday falls thru
Contains unread posts
Contains no unread posts
Thread is closed
You have posted in this thread
Back to top
