All posts made by unijabnx2000 that members have liked.
If i would have had these in 15 and not 17's I would of kept mine for sure.
http://i211.photobucket.com/albums/bb110/nx2000det/car/SSL20981.jpg
I talked to Tad and he's going to make a shorter mid-shaft for the OEM LH side B15 axle..
Going to take a while - about 4-6 weeks.
OMFG!!!
I never disconnected this. So i thought it still was connected....
But my father must of disconnected the brake booster hose and didnt say anything.
Lets see if its fixed now... Goi...
B15 axle - top
B13 axle - middle
the "part of bearing the hub are pressed inside" over - on the B15 axle - bottom
The lengths are very close... But the "hump" at the end of the splines on the B15 ...
At this point, i'll be happy to get my car together and drive it around to get any kinks out before leaving for the convention.
OK thanks guys,
I have the specv cables
I spent a while fighting them today, then had to wrestle them back out... now that the shifter assy is mounted down, i'll try to push them back b/t the fire...
Ive been studying...
https://www.youtube.com/watch?v=nAJH2rc1z1o
[url= URL=http://www.atlantamotorsportspark.com/pdf/Turn%20_numbers_%20main_%20track.pdf][img]http://www.atlantamotorsportsp...
Ive been studying...
https://www.youtube.com/watch?v=nAJH2rc1z1o
[url= URL=http://www.atlantamotorsportspark.com/pdf/Turn%20_numbers_%20main_%20track.pdf][img]http://www.atlantamotorsportsp...
if for some reason I dont get my car done, i'll still drive something there
I should have my swap done in the next two to three weeks for the convention.
I'll be headed to Hollywood/Orlando FL afterward. So you guys can look over my NX when I get there.
I should have my swap done in the next two to three weeks for the convention.
I'll be headed to Hollywood/Orlando FL afterward. So you guys can look over my NX when I get there.
Am i really the first NX to be doing the swap??
I should have my swap done in the next two to three weeks for the convention.
I'll be headed to Hollywood/Orlando FL afterward. So you guys can look over my NX when I get there.
I should have my swap done in the next two to three weeks for the convention.
I'll be headed to Hollywood/Orlando FL afterward. So you guys can look over my NX when I get there.
Is that the stage 3??
I went with the spec stage 3+
also to get an accurate idea of the tune based on the look of the plugs; you are supposed to start with fresh plugs and shut off the car during a run and immediately check them.
you may want to find a dyno to verify how accurate your sensor is, mine only lasted about 2 years before I had to stop using it (although that was b/c of the short time I was running extremely rich...
im not a tuner, but I think the target afr for cruising shouldnt go leaner than low 15's
Yeah that doesnt sound like what I was thinking. But If lowering the gap doesnt help, id look back at the tune again though.
http://i211.photobucket.com/albums/bb110/nx2000det/car/Wiring/SSL20498.jpg
http://i211.photobucket.com/albums/bb110/nx2000det/car/Wiring/SSL20503.jpg
http://i211.photobucket.com/albums/bb110/nx2000...
New power wires for the coils and the injectors (injectors had 4 wires running most of the way back to the ECU)
http://i211.photobucket.com/albums/bb110/nx2000det/car/Wiring/SSL20478.jpg
Still got...
Put shrink around some of the factory "tape"
http://i211.photobucket.com/albums/bb110/nx2000det/car/Wiring/SSL20457.jpg
Soldered and almost shrunk - IAT sensor plug
http://i211.photobucket.com...
Got the subharness for the coilpacks done.
Since the pins for the connectors only support 18AWG
I had to split the power wire down to 3 smaller wires.
I also doubled the ground and made it a li...
I start tearing mine down for the 6 speed swap this coming week....