All posts made by Sentraga that members have liked.
They're NOT the same cap. The b15 cap is larger.
I know autozone isn't the say all, fix all but look up the caps for the two cars.
They're two different part numbers.
G20 - JA9032
http://cont...
The proper auto parts store replacement cap for the VE distributor comes from a
[S]2002[/S] 2001 Nissan Sentra with the SR20 NOT the G20.
https://lh5.googleusercontent.com/ffULmMSkquf-CIiOnR0x1U5T5wgoFyPffmFAzDOUdJA=w769-h577-no
Aren't you getting Nismotronic.?
It can control VVL also...
If you're ready to build it "right" then get an ecu with a tunable daughteboard or a standalone.
Sure it'll run on all DE stuff and an MSS but that's in no way the right way.
If you're ready to build it "right" then get an ecu with a tunable daughteboard or a standalone.
Sure it'll run on all DE stuff and an MSS but that's in no way the right way.
If you're ready to build it "right" then get an ecu with a tunable daughteboard or a standalone.
Sure it'll run on all DE stuff and an MSS but that's in no way the right way.
I don't know about this newest design, but his website lists the old design wheel spacers 4/5x114.3 bolt pattern.
http://www.tdmimports.com/image/cache/data/TDMimports%20wheel%20spacer-500x500.jpg...
I don't know about this newest design, but his website lists the old design wheel spacers 4/5x114.3 bolt pattern.
http://www.tdmimports.com/image/cache/data/TDMimports%20wheel%20spacer-500x500.jpg...
I think he's looking for the 200sx (b14) seals, since it's in the 200sx section.
Having both cars, so I speak from experience,
No.
For everyone's future reference:
76500J - Is a plastic holder that is designed to have a screw through it.(The two 10mm bolts that hold on the s...
Having both cars, so I speak from experience,
No.
For everyone's future reference:
76500J - Is a plastic holder that is designed to have a screw through it.(The two 10mm bolts that hold on the s...
Having both cars, so I speak from experience,
No.
For everyone's future reference:
76500J - Is a plastic holder that is designed to have a screw through it.(The two 10mm bolts that hold on the s...
Worse, from what I've been told. Car would have to be certified by Nissan Mexico to meet Mexican "DOT" standards. i.e. It'd cost you the same as just bringing it here.
Now if you were to import ...
I can vouch for these. Been running them on my car for over 3yrs now.
I'll be unavailable the first, second, and last weekend of oct.
So 10/17 would be perfect.
(paging nissanboi)
Yea, anytime you do suspension modifications(swaybars, braces, things other than struts) you're not supposed to tighten it with the car in the air.
The suspension should be at ride height, otherwi...
The only thing I can help with it going into timing mode, sorry I'm not much help with the rest of it.
Let the engine warm up to normal temp.
Disconnect TPS
Rev engine to 3000rpm THREE times.
...
The only thing I can help with it going into timing mode, sorry I'm not much help with the rest of it.
Let the engine warm up to normal temp.
Disconnect TPS
Rev engine to 3000rpm THREE times.
...
look at the place where the temp sensor was on the original engine. Next to it is one other sensor that has only a spade connector.
The red temp sensor you used is for the ECU for warm up enrich...
look at the place where the temp sensor was on the original engine. Next to it is one other sensor that has only a spade connector.
The red temp sensor you used is for the ECU for warm up enrich...
It'd be a nice part if they worked for fuel injected vehicles.
Pressure ranges from 2-14 PSI ONLY; this is for carburated vehicles.
For pricing-
http://www.sr20-forum.com/tdmimports-kuo-s-garage/77837-b13-super-rare-window-molding.html
I don't have to ask, the shop right down the street from me has a summer special of $89.99
Rear motor mount would be my guess.