All posts liked by pedro666
1 |
I feel like every post I've made here lately is about the TPS :)
Readings on ground pin:
0 Ohm resistance to ground
Readings on signal pin:
Throttle fully closed 0.45-0.55V
Throttle partia...
TunerView App Testers Needed!
This piece of engineering arrived yesterday:
http://i.imgur.com/3qhcX4z.jpg
Time to start programming. I simulated a PWM output, and sampled it back into the microprocessor. You NEED an oscillosco...
You can always save the log manually if you have issues with permissions.
I want to add a little information for anyone interested.
This is a sequential ignition system and functions just like OEM
This can be used in a CNP, or COP configuration. Capacitive discharge sy...
By the way I like the fact that you're at least trying to figure something new out most people on here just want to plug in and go. It's good to see someone trying to hack the system .free thinking...
Quick update: Hard wired the system in today minus the completed proto-board. Cleared up 90% of the misfire issue. After setting timing repeatedly, I think I have a good idea of what is going on. S...
You won't be able to use the 70a pinion shaft in a 70v box.
The pinions and ring gears are matched pairs, the ring gears cannot be interchanged either, V boxes have more bolt holes.
Yes, the TV2 and RD1 are both supported with NismoTronicSA.
TunerView LCD, NismoTronic - Nissan ECU Tuning
meanwhile at custom plenum creations, ariel has stepped it up to a whole new level.
[URL="http://i1334.photobucket.com/albums/w660/sss4me/billetmanifold_zps704c8447.jpg"]http://i1334.photobuck...
They offer one of those as well.. it is called the TunerView II.
I had one in my old 1998 Civic, it displays the same things that the RD1 can.
I am not sure if they will end up being supporte...
I want to bring this back from the dead :D
So I went for emissions yesterday and took my laptop with me to do live A/F correction. The tester had zero issues with my adjustments during the test ...
4:th attempt
Result: Pass :D
http://i.imgur.com/yt5Wo8r.jpg
These were the readings. Nismotronic settings, "Enable Closed Loop" [X], "NB02 Closed Loop" [X].
I deviated from the first post...
+1 on the OR function! I'm wiring in an intercooler sprayer, and would like to make it go on if IAT > x degrees OR load > x mbar
Would it be able to assign names to the Generic Outputs?
Like th...
carbon fiber 3d printed
https://markforged.com/
you have a turbo with a n/a header?
So that everyone knows, we are not totally against making stuff, but we do need the support to be able to gain the interest in making products for you guys. Check out the VVL RWD swap intake that's...
keep your P11 VE and buy stuff for it. Valve springs, hicomp pistons, rods ect ect ect.
i can't speak for the usa, but here's an example of what (i think) is the cheapest way to make a custom intake. use your sr20ve runners, make up some custom longer runners/bellmouths,add a plenum,t...
Freshly washed
[url= URL=http://s31.photobucket.com/user/cortrim1/media/20130523_194713_zps99c5f12c.jpg.html][img]http://i31.photobucket.com/albums/c393/cortrim1/20130523_194713_zps99c5f12c.jpg[/i...
http://www.youtube.com/watch?v=i2j2c7uUcMc
photos
[url= URL=http://s1261.photobucket.com/user/spoiltone/media/buggyadaptor1.jpg.html][img]http://i1261.photobucket.com/albums/ii599/spoiltone/buggyadaptor1.jpg[/img][/url]
[url= URL=http:/...
http://i62.photobucket.com/albums/h99/ga16de/DSC04315_zpsd24f4601.jpg
1 |