All posts liked by nismo94tuner
Try it. You really won't notice much of a difference.
I find it hard to believe that with just the header alone it gained 20whp. Stock VE with Xcessive plenum at 166whp? It's a combination of things that could result in 20whp gains. Car must of not b...
http://www.titantalk.com/forums/attachments/buy-sell/39850d1174610085-fs-17-x8-infiniti-qx4-stock-rims-sspx0204.jpg
These. I'm a sucker for them.
Yep, I absolutely enjoy those factory wheels on those QX4s.
I wanted one so I understand the allure.
Unless you have to replace the alternator and you have man sized hands
rear main seals and rear trailing arm bushings and on high mile vehicles the coolant crossover o rings are the only really big issues, I ever seen, I owned one, it was killer, but I had a 94 Isuzu ...
535whp grocery getter
[url= URL=http://s31.photobucket.com/user/cortrim1/media/20140719_151850_zps3079324f.jpg.html][img]http://i31.photobucket.com/albums/c393/cortrim1/20140719_151850_zps3079324f...
Easier than Nissan, that's for sure !
LHP
nismo94tuner we got a gear stack from a known reputable SR20 mechanic whith gears bound up just like that. The problem I believe was that the gears were pressed on to the shaft incorrectly so that ...
It is not worth it because it takes $$$ and time to INSTALL the SSAC, then pay for Dyno time, uninstall then Install the Medusa again all in the same day just to get some numbers. It is also hard ...
The 3 piece front should have significant weight savings as well as a wider design in the fenders so bigger tires can be fitted onto the car.
As for being completed it's the never ending B13 Sen...
give the solenoids 12v(battery) constant and switch gnd. I use the low side driver for injector 6 for my vvl. Its also a good idea to use a relay(weak trigger to strong trigger) between the ems and...
Putting on a carbon fiber hood thanks to nismo94tuner !! :)
No love for my post even though i'm trying to help a brota out?
IL AEM EMS V1 for sale - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum
They will hurt your mph a lot as well for being so tall.
Just keep the pressure fairly high and you should be able to stay away from bogging. Launch like Bes said, and pre load the car hard. It ...
Here's the best on my DD Civic:
https://www.youtube.com/watch?v=ePY93kPuW_E&list=UU2i7p3NF_2dmMTwwMrooo-w
And on a side note... I am looking to start working on my 200sx... Looking to go 2.1L.....
You can use the Hot Cams shims as a much cheaper alternative. They are a hair smaller diameter, but work just fine in my 8500 rpm DET.
It combos pretty well, you gain +2 in dex and +3 in accel. Flywheel gives -1 to strength but the P11 tranny makes up for it with a +2 str modifier.
i am very close to him and will get in touch with him
only place bes adds weight is the stomach from that albanian cuisine
will you just drive the damn thing already
I ran 100-125 shot of nitrous through my 10:1 DE for several years and the car never skipped a beat and this was with going through 2 bottles a week. It was also my DD for a majority of that time....
I had them on my Miata. They worked just fine.
http://img.photobucket.com/albums/v511/neonmike22/Meotter2/Bilstein/bilsteins10.jpg
go 88mm and be done. dont even bother putting an NA motor together without going to 88mm. especially with your goals, the bore will do a lot for overall whp figures