unijabnx2000's Likes Given

-Run #5 was his car as it stood mechanically but tuned to that setup.
Sr20ve stock cams
Ssac header
Intake pipe
3" exhaust
Stock cat in place

-Run#10 was the tri-y header installed tune adjustme...

Found the right one at harbor freight and got everything taken care of

Eh, they were kind of what I expected. I enlarged 6 holes in total with a 14mm drill. I had to cut and reweld one flange, and I think I know why.

http://i.imgur.com/I80HzsX.png

During product...

We have done literally about 100 E85 conversions at the shop in the past 2 years or so (we have a station 100ft from our building).

The lines shouldn't need upgraded UNLESS you are planning on out...

Eh, I have been running those type of clamps for 4 years with no issues whatsoever. Clearance is the main issue, it's not possible on some cars. B13 has plenty of room, so it works here.

If you ar...

A little update

you guys just need to block each other and get over it....its been a year and a half allready.

just FYI, if Drive Shaft Shop is trying to charge MORE than $100 per set of b13 hubs, ive got an invoice that you can throw at them. $100 a set is what they charged me after some haggle.

also to ...

unijabnx2000 Unsure at the moment. When I get a chance to measure the b13 distributor and cap, I can adjust the design accordingly. Currently this cap is for the b14+ distributor. Chances are it wo...

Newest design is rock solid in bench testing. Night and day compared to what I showed for my final presentation. Trying to install this weekend to monitor the cycles, hopefully follow up the weeken...

[url= URL=http://smg.photobucket.com/user/TRUSE-R/media/60F91DD2-CC27-4C36-976E-298F8CCB2E05_zps04oqeci9.jpg.html][img]http://img.photobucket.com/albums/v175/TRUSE-R/60F91DD2-CC27-4C36-976E-298F8CC...

Gauge cluster 194 three bulbs
HVAC 194 one bulb
Cigarette lighter 74 one bulb

Prepping for finals. Project presentation with the head of the Engineering Dept, and maybe the school president. My school is kinda blowing this out of proportions. Looks like they are trying to us...

http://www.sr20forum.com/gallery/data/500/20v_eccs_wiring_diagram.jpg

SR20VE 20V ECU Pinout.

1 --
2 O2 sensor heater control signal
3 --
4 --
5 --
6 --
7 --
8 --
9 VVL solenoid contro...

Piston rings

Parts

The glitch is all taken care of now, on the bench anyways. But here is a demo of two coils running on the DISSR using the JimStim as the driver. Basically all this is showing is the reset issue cau...

did you ever ship these back? If so, what is the tracking?

Just to update this my detonation issues were for a bad tune where I had A/F ranging from 12.5 to 13.0 so you can imagine why the high egt temps. After fixing the tune not a single problem has ha...

Homemade shift boot for 6 speed out of P11 sport seat suede insert

[url= URL=http://s147.photobucket.com/user/mickeyser/media/20151112_175813.jpg.html][img]http://i147.photobucket.com/albums/r2...

Not yet. John is going to be running the K20 coils when I get a controller out to him. Realistically though, any 5v(sig) induction coil will work with this. It can even work on falling edge coils t...

New design is functioning. In class demo will be on Tuesday. Its currently in a modular design but is being scaled down.

http://i.imgur.com/LnFhtQW.jpg?1

So basically the glitch i was running in...

Well here's a lil video for you guys.. Sorry these pretty shakey.. the country roads are a bit bumpy an it's hard to keep the phone steady lol

http://youtu.be/gSY4rK04V0o

You might notice a lil...

There were some questions about reproducing my controller, here and other forums. Getting rid of the pics was the easiest way to make it hard for anyone to copy it. I'm a few grand into this projec...

yep my hotmail is working now