All posts liked by JKTUNING
I was a little reluctant about posting my board, but considering this design didn't produce the best result and will likely meet the chopping block, I think its ok to share. This was made using a t...
A reschedule looks to be a good option. Wouldnt that mean JKTUNING can make it?
We are now Nismotronic powered. Played around with it a bit this weekend seeing how coil dwell affect idle and low load throttle response. Didnt get very involved though. I am converting now over t...
Gone mine today. Pulled the ECU out of the car, will solder the header on later.
Some update:
App works fine. Found and fixed a few wrong value conversion (IAT,ECT,TPS). 30 Status indicators added and works fine. I need to add some values what i not added yet (like inputs, kno...
Awesome!
I picked up a trashed android phone and flashed it to Lollipop (5.0.2), gonna see if a lowram unit can run this application, else I will switch to a dedicated tablet
http://i.imgur.com...
Hi guys. I try to answer some question.
IOS version is work in progress. Its need more time to make it.
Moates working on a wifi adapter for NEMU/Demon/QH, so the IOS version will using...
This piece of engineering arrived yesterday:
http://i.imgur.com/3qhcX4z.jpg
Time to start programming. I simulated a PWM output, and sampled it back into the microprocessor. You NEED an oscillosco...
Never in my life would I have believed I would be where I am with this project. I am incredibly grateful for all the interest this community has shown. I am personally grateful to John at JK Tuning...
its amazing how well things work when you wire them up yourself :) :)
I just got the new aem wideband installed, wired it into the nemu breakout box...everything works perfectly :)
thanks for the specific pin #s..i should have no problems wiring in the new AEM
edit: so after removing the old gauge and all of the wiring I found out why I was never able to get it working prop...
There are great solutions ready to be purchased, but they all cost a significant amount of money. Let's crack out the microprocessor!
Fiddling with my old ATMega644p, this is how it looked last ...
I want to add a little information for anyone interested.
This is a sequential ignition system and functions just like OEM
This can be used in a CNP, or COP configuration. Capacitive discharge sy...
CNP/COP conversion for OEM ECU
DALA - Thank You so much! I did exactly what you've posted and it works amazing!
This has brought back the joy of my P10.
Thanks again!
You made the right choice man, nismotronic is about 50 times simpler then MS and is a true plug and play. JK tuning has so many. Ase tunes that when you upgrade your parts you can just upload a new...
Using a hp stream 7 tablet with a mountech snap 3 mount. Fits perfect doesn't come disconnected on hard runs and runs nismotronic flawlessly. You just need to purchase a separate adapter but oth...
You made the right choice. I started tuning on the NEMU and it is easy to use yet there are enough features to really dial in the car to get it to run correctly. Read a lot on it and take your time...
When using boost by gear the ECU will use a specific duty per gear.
A gear is determined by the VSS and RPM. Because there is no input of gearing, tire seize ect Nismotronic has a paramter ca...
You can run either MAF or MAP with a MAC boost control solenoid controlled via Nismotronic.
Dala is correct here. Nismotronic does not need to know your gate pressure. It does not need to know this to do what you want it to. Also it does not need to know manifold pressure and dosnt use...
I want to bring this back from the dead :D
So I went for emissions yesterday and took my laptop with me to do live A/F correction. The tester had zero issues with my adjustments during the test ...
http://i110.photobucket.com/albums/n104/DaMasterPNut/SR20VE/SR1620VEECUpinoutdiagram.jpg
If this is correct, take pin 102 & 106 on the VE harness, and connect it to pin 11 on the ECU
+1 on the OR function! I'm wiring in an intercooler sprayer, and would like to make it go on if IAT > x degrees OR load > x mbar
Would it be able to assign names to the Generic Outputs?
Like th...
I put in the numbers that John recommended and all I can say is "WOW". Sounds great and built a lot more boost. I don't think I will need that much cause I already have issues with spinning the sli...