BenFenner's Likes Given

1991 Nissan Sentra SE-R

Buy this one.

Does this fit in this category ;)

http://www.mazworx.com/pics/DSC06735.jpg

the only two worth bothering with are Ultra wires (good freaking luck finding them, but ask Miko if you're REALLY serious) or OEMs. I've heard quasi-good/quasi-bad stuff about taylor 10mm wires, b...

T Shirt Thread

dont pay over $400 for that

A few notes on that picture.^


That's a GT2560R on a Bluebird manifold, and as you can see, the drain lines up perfectly.
On a GTiR manifold, it won't line up nearly as well, but a short piece...

T25 on GTiR manifold.http://i432.photobucket.com/albums/qq47/chriscar2/Engine_Assembly/aap.jpg

C

Well im officially back in the states sitting in Atlanta waiting for my flight to Texas. Ill be getting started on everything this weekend. Lots of pics to come in my thread.

Can we reverse that, make thread titles black and names gray?

I'm finally spending some quality time with the B13. Just mocking everything up at this point.
94 SE-R Turbo install pictures by chriscar2 - Photobucket

When's the last time anyone saw a brand ...

Working on another bellmouth j-pipe for a bluebird setup...almost done

http://sphotos.xx.fbcdn.net/hphotos-snc7/577648_310261739044254_170000483070381_726922_1709574810_n.jpg

and, the start of a ...

there's a design in my head, but I don't have the fab equipment require to build it yet. the design is a little outside the box but function and form will be top notch!

my brothers and I will be f...

Tacked up a GTiR bellmouth for a - member earlier today, should have it done in a couple of days.

https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/294464_178330368904059_170000483070381_38508...

Almost have a GTi-R screamer part done!

http://turbofx.net/wp-content/uploads/2011/07/gtir-o2-hsg-screamer-01.jpg

http://turbofx.net/wp-content/uploads/2011/07/gtir-o2-hsg-screamer-02.jpg

http:/...

A few more pictures...

http://turbofx.net/wp-content/uploads/2011/07/gtir-recirculated-down-pipe-04.jpg

http://turbofx.net/wp-content/uploads/2011/07/gtir-recirculated-down-pipe-05.jpg

http://tu...

Bellmouth design almost finished, just need to weld up the 3 bolt flange and then surface the part.

http://turbofx.net/wp-content/uploads/2011/07/gtir-recirculated-down-pipe.jpg

http://turbofx.n...

GTiR is taking shape.

http://turbofx.net/wp-content/uploads/2011/06/sr20-02-hsg-gtir.jpg

For those who are interested in screamer pipes, will you be running A/C? Reason I ask, is that dump tube ...

Thanks guys...much appreciated :bigthumbup:



Definitely, fitment and ease of installation are very high design priorities. When the next part is finished, I'll document the install process and t...

Started on the recirculated waste gate design today...went a little different route with the bends.

http://turbofx.net/wp-content/uploads/2011/06/sr20-02-hsg-pie-01.jpg
http://turbofx.net/wp-cont...

I have a compressor that came on my Avenir ( not sure if thats compat ) if so I could ship it to ya for free..

NO A/C Here

I would be interested in :


Avenir/Bluebird compatible ( direct replace...

You should just scrape off your VVL letters from the 20V and sell it to Dan ;)

Getting the Pulsar ready. Taking the clutch down to replace with a better slipper type clutch and inspecting the gears. A bit more testing on it to come soon hoping to go low 9's high 8's @ the Con...

thats far to much ground to cover.

my advice and ive done it like this before, pop the hood, get out the simple green, spray and scrub everything down, rinse it off really well.

let everythi...

Lower half before....
http://i531.photobucket.com/albums/dd354/MADTEC/PULSAR%20GTI-R/IMAG0298.jpg
http://i531.photobucket.com/albums/dd354/MADTEC/PULSAR%20GTI-R/IMAG0299.jpg
http://i531.photobuc...

what is e85