Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: Minnesota/University and surrounding areas

+ Reply To Thread
Posts: 231-240 of 317
2009-06-09 02:05:33
#231
I pulled on him pretty good, but it was quick. I wish I had a chance to go against cory's car and most likely loose
2009-06-15 17:06:23
#232
In case anyone is interested in helping I am getting a new motor, but I need to swap over everything. I don't have a hoist or stand so if someone has either of those that I could borrow that would be great since I am going to be a little tight on cash. Here are some specs on what I am getting and I got it for a little less than a stock bb/avenir:
-9.1:1 Weisco Pistons
-Eagle Rods
-ARP Rod Bolts
-Block Bored and Honed to .020 86.5mm
-Multi-angle Valve Job
-Engine Balanced
-Never been started

I'm making sure to come back bigger and better.
2009-06-15 23:59:07
#233
nevermind this post
2009-06-18 01:11:13
#234
I know a guy with a hoist, I have no idea how to get it to you. I also can help you out. We should get er done before the meet

Sniper, we gonna roll up to your place?

Anyone know of a good place to get exhaust welded up?


Originally Posted by MN_SR20
In case anyone is interested in helping I am getting a new motor, but I need to swap over everything. I don't have a hoist or stand so if someone has either of those that I could borrow that would be great since I am going to be a little tight on cash. Here are some specs on what I am getting and I got it for a little less than a stock bb/avenir:
-9.1:1 Weisco Pistons
-Eagle Rods
-ARP Rod Bolts
-Block Bored and Honed to .020 86.5mm
-Multi-angle Valve Job
-Engine Balanced
-Never been started

I'm making sure to come back bigger and better.
2009-06-18 02:52:19
#235
I don't think I will have the motor for a bit since I have to wait for the guy to ship it and money is tight because blowing this motor couldn't have come at a worse time.
2009-06-18 05:08:58
#236
Originally Posted by djcslice
I know a guy with a hoist, I have no idea how to get it to you. I also can help you out. We should get er done before the meet

Sniper, we gonna roll up to your place?

Anyone know of a good place to get exhaust welded up?


My shop and parking lot (Freshly paved BTW!) are ready whenever you lazy MN guys say the word!!!!!

PM me about the welding...... we can do anything you need.
2009-06-18 15:02:41
#237
Anyone know of a good place to get magnaflow parts? I have some one order but they wont be here till the 23rd. I was hoping to get this welded up before the meet and then return the parts I get in the mail to the place I buy them locally.
2009-06-20 15:07:22
#238
minnehaha falls

this is where we will be at. If its busy we can find another place close by.
2009-06-20 16:41:43
#239
Originally Posted by djcslice
minnehaha falls

this is where we will be at. If its busy we can find another place close by.


ya that place is always packed, maybe fort snelling, there are a couple huge lots that are always available... me and kong had a pretty big group meet up there a few weeks back

the lot was like a mile or two form minnahaha falls
2009-06-21 11:21:46
#240
meet>me totally forgot
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top