Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: Ebay header 2.5" secondary

+ Reply To Thread
Posts: 1-10 of 29
2011-11-12 00:39:10
#1
Ebay header 2.5" secondary
Hey fellas. I just picked up an ebay header for 86 and some change shipped. I got it today. Measured it and confirmed that it's the 2.5" version. There are three more on there right now. You can see in the picture which one I'm talking about. They show the primary tubes at 2" and the secondary exit at 2.5"

I measured the primary and its 1 7/8" wide not 2". Close enough though. Flanges are 3/8" thick. It definitely looks like what the SSAC looks like. Box that it came in says dna motoring HDS- G2091

Just giving everybody a heads up. Not a bad mod for under 100 bucks.

I used "Sr20 header" as my search phrase.

Links to the auctions.
http://www.ebay.com/itm/NISSAN-SENTRA-SER-200SX-INFINITI-G20-P10-SR20DE-2-INLET-STAINLESS-EXHAUST-HEADER-/330635905980?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item4cfb6f8bbc

http://www.ebay.com/itm/NISSAN-SENTRA-SER-200SX-INFINITI-G20-2-0L-SR20DE-STAINLESS-STEEL-EXHAUST-HEADER-/110768842588?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item19ca56675c

http://www.ebay.com/itm/NISSAN-SENTRA-SER-200SX-INFINITI-G20-P10-2-0L-SR20DE-STAINLESS-EXHAUST-HEADER-/110774245411?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item19caa8d823
Last edited by TrackJunky82 on 2011-11-15 at 16-59-26.
2011-11-12 06:41:33
#2
Same one I got a week ago. The real deal, and it has studs that thread into the header flange instead of those older ones with bolts to fiddle with.
2011-11-12 07:12:36
#3
yeah i had these they are good except i had to shave a bit off to fit it but its a good buy
2011-11-12 08:09:44
#4
Originally Posted by mynissanb13
yeah i had these they are good except i had to shave a bit off to fit it but its a good buy


shave what off?
2011-11-12 10:00:33
#5
Originally Posted by Barney'sB14
shave what off?


^^^^^^^^^^^^this
2011-11-12 21:10:46
#6
I'm not sure what mynissanb13 had to shave, but a had to ream out a hole or two on the header flange with a dremel to make it fit. No big deal really. I didn't install the header from the new one I got, as they are both the same. The only difference would be the secondary. It's only 2.5 inch, or 2 inch, for either one, starting right before the flex pipe back.
2011-11-13 02:01:21
#7
Originally Posted by tswii
I'm not sure what mynissanb13 had to shave, but a had to ream out a hole or two on the header flange with a dremel to make it fit. No big deal really. I didn't install the header from the new one I got, as they are both the same. The only difference would be the secondary. It's only 2.5 inch, or 2 inch, for either one, starting right before the flex pipe back.


yeah the holes were a bit off it was no problem tho
2011-11-13 07:50:51
#8
Do you think this will be good on a ve?
I know ill probably have to port match it
2011-11-13 14:51:03
#9
Alot of guys are using the SSAC on the VE. Yes you will have to port match. Or just make adjustments to the holes so you can move the header into a better position for the ve.
2011-11-13 16:29:03
#10
I have been looking at this same header on Ebay for a few days now and I am still trying to figure out...would this header work on a 91 se-r. Thanks!
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top