Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: N1 vs 20V blog, ate TB screw, fixed... i think.

+ Reply To Thread
Posts: 1-10 of 147
2012-04-26 02:47:22
#1
N1 vs 20V blog, ate TB screw, fixed... i think.
Cam comparison 20V vs N1 "drop-in" results.
The Test: Drop in comparison between N1 and 20V cams.
The Dyno: Dynojet 248C upgraded to 2000whp capability.
Date: ‎4/‎25/‎2012
The Car: Coheed's Super Sentra


The Setup: 8.5:1 compression, tubular long runner manifold, Supertech springs and retainers, JWT computer, Stock head/intake manifold, Precision 6262 bb. And supporting mods.

Special Thanks to Vadim for making this test possible. Without his trust and temporary donation of N1 cams this test would not have been possible. big thanks to Fast-Times dyno services. JC allowed me to swap cams on the dyno to get the most accurate back-to-back results.

Runs were done 20V low, 20V high. Then N1 low, N1 high, then N1 low again. Due to some boost irregularity and some dyno mishaps, the N1 low had mixed results.

Dyno comparisons were done starting at 2000 rpm for low boost. Boost controller was set to its lowest settings. The boost did fluctuate slightly between runs, it was something out of my control. But runs were around 1-2psi of each other.
Here is the low boost runs: Blue is 20V, red is N1.


Results: The 20V cams performed amazingly well on low-boost of 11psi. 365whp compared to the N1 at 342whp. This is a difference of 23whp. For some reason, the N1 cams consistently under-performed to the 20V cams. Though boost was slightly lower by ~1psi, and there was some issues on the dyno, the 20V without a doubt made more power on low boost.
What couldn't be forseen however, is the bottom end power delivery. The N1 in every run produced more power on the bottom end, in various areas. I would like to do more testing with the N1 on low boost to see if I can get it to make what the 20V made. The issues on the dyno meant the N1 low boost had to happen after high boost pulls to get an accurate reading. However, this may have cause some slight heat soaking. More testing will be required on low-boost runs. I encourage others to post their results.

High boost runs are when things get really entertaining: Blue is 20V, red is N1.


The N1 cams outperformed the 20V here, generating 516whp on only 19psi boost on N1 and 491whp on 20V. A difference of 25whp. The N1 also didn't lose any bottom end to the 20V cams. There was a dip in power delivery on the N1 coming on boost. The power onslaught was so severe, boost went to 24psi momentarily before dropping back to 19psi. This caused a bit of spark blow-out. This was remedied by closing the gap and following up with another pull and it made 505whp. There was some heat-soaking going on for sure, but pull after pull the N1 made over 500whp on 19psi.

I encourage anyone else pursuing this kind of cam swap to do a comparison as well. The N1 cams don't seem to have any negative effects, if you can deal with less power on low boost. The N1 can switch ealier and start making power faster. The cams are extremely quiet on low, but scream like a banshee on high. They get 3x louder, they are flat out abnoxious.

Feel free to discuss. There are variables at play here, but it is what it is.
Last edited by Coheed on 2012-06-17 at 03-57-27.
2012-04-26 02:58:43
#2
YOU DA MAN!!

glad to see you finally hit the 500 mark, who would of thought it would of took n1's to do it.. and on only 19psi!! Grats man!

i wonder if playin with the cam switch points or possibly even using different points for the intake an exhaust would help with the switch over? or maybe dialing them in, although i know you said you didnt wanna mess with that.. but now that you know what the n1's can do maybe you could concentrate on furthing dialing them in.
2012-04-26 03:04:33
#3
The 20V like the intake kicking first, then the exhaust. The N1 are the opposite. The exhaust cam kicking early helps aid spool. You cannot go wrong with any of the cams. They both did extremely well. The 20V did better on low boost, and N1 better on high boost. But all things considered, the cams are amazingly close. Run-to-run saw power ranges within 15whp typically. Heat played a big role.

The N1 low dyno was done before the high boost run, but the dyno had issues and runtime errors caused the dyno to not read. We were strapped for time, so I carried on to high boost. It did awesome, so I went back to low boost. The engine was hot, and there were other issues starting to arise. So I did the best I could.
2012-04-26 03:07:54
#4
well great work man, we really appreciate you sharing your findings with us. keep up the good work!
2012-04-26 03:09:05
#5
From 200whp to 370whp in a matter of 400rpm. Damn.

Thanks for the kind words Lynch.
2012-04-26 03:11:26
#6
i cant wait to get mine on the dyno! my setups no where near yours but i'd like to get it tuned an go destroy some other cars at the strip!

2012-04-26 03:14:27
#7
nice indeed!

making me regret not taking the N1'd!
Last edited by Keo on 2012-04-26 at 03-19-27.
2012-04-26 03:20:15
#8
Very awesome man. Good job on the results and congrats at finally hitting that 500+whp mark at under 20 lbs of boost. Crazy good numbers. Glad to see the car is performing really well. 19psi must feel really really good. Thats a good powerband right there.

Good solid gains from the n1's without doing anything but dropping them in. Cant go wrong there.
2012-04-26 03:20:26
#9
nice indeed ....hmmm
2012-04-26 03:21:08
#10
that shi cray
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top