Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: nitrous in ve

+ Reply To Thread
Posts: 51-60 of 132
2009-06-03 15:14:56
#51
Originally Posted by qwkse-r
well this morning went the crank the carup and go to work when there was a very strong smell of fuel,so i poped the hood and sure as **** it was leaking from the fuel rail,or somewhere around there.it doesn't seem to be the injector o-rings,seems to be from the fuel lines....it was dripping pretty bad...i wonder if all the 55 psi fuel pressure caused this,though before this noticable leak i have been smelling fuel around the motor area,a slight smell though.i wonder if this is my culprit for running lean,you know losing pressurein all from leaking


check you in line pressure gauge they leak if you don't use the right sealant. High task gasket sealer made by permatex is the only stuff that I know of that can take direct contact with gas. Don't use rtv or teflon tape. You can definately run lean from a fuel line leak.
2009-06-03 15:46:34
#52
Originally Posted by cortrim1
check you in line pressure gauge they leak if you don't use the right sealant. High task gasket sealer made by permatex is the only stuff that I know of that can take direct contact with gas. Don't use rtv or teflon tape. You can definately run lean from a fuel line leak.


its not leaking from there,its looks like from the hose between the nismo fpr and the fpr look-a-like...
2009-06-03 16:26:43
#53
Originally Posted by qwkse-r
its not leaking from there,its looks like from the hose between the nismo fpr and the fpr look-a-like...



I would replace all the fuel lines and clamps. the clamps will go bad if you over tighten them.
2009-06-03 16:51:49
#54
Originally Posted by cortrim1
I would replace all the fuel lines and clamps. the clamps will go bad if you over tighten them.


yep thats what im going to do after work....hopefully thats the culprit to me going lean so i can lower the fuel pressure...
2009-06-04 00:05:59
#55
well changed out the fuel lines and fixed the leak,but no luck with the a/f ratio,it still runs the same at 55psi fuel pressure...12.7-13.4's...starting to lean towards dirty injectors
2009-06-19 16:33:19
#56
I will be running some juice through my VE very soon. Will be sure to post results......I will also be customed tuned for race gas and have another set of chips for n/a duties.
2009-06-19 17:56:37
#57
im considering n1's or sr16 cams with my nitrous set-up...what do you guys think,i also am gonna stick with stock s&r for now......gonna go direct port or just bump the single fogger to 100shot
2009-06-19 18:05:09
#58
Originally Posted by qwkse-r
im considering n1's or sr16 cams with my nitrous set-up...what do you guys think,i also am gonna stick with stock s&r for now......gonna go direct port or just bump the single fogger to 100shot


love my n1's and they work fine on the stock s&r. Your good to 8500rpm on the stock s&r with the n1 cams. Direct port is the way to go . You may want to get a window switch for the n20 so you don't over rev.
2009-06-19 18:06:36
#59
Originally Posted by qwkse-r
im considering n1's or sr16 cams with my nitrous set-up...what do you guys think,i also am gonna stick with stock s&r for now......gonna go direct port or just bump the single fogger to 100shot


Well I am going to be using sr16ve cams without s/r's and keep the rev limiter at 8k, no need to go higher. I am also going with a 100 shot single fogger, but will eventually upgrade to a DP syetem too. I bought my stuff at dynotune, which from what I heard is a very good company and they have excellent products and gret support to go along with it. They also have some really neat stuff too. heck out there website
2009-06-19 18:15:13
#60
Originally Posted by jonwepa
Well I am going to be using sr16ve cams w/ s/r's and keep the rev limiter at 8k, no need to go higher. I am also going with a 100 shot single fogger, but will eventually upgrade to a DP syetem too. I bought my stuff at dynotune, which from what I heard is a very good company and they have excellent products and gret support to go along with it. They also have some really neat stuff too. heck out there website


yep dynotune for nitrous man,got a bottle warmer kit and purge kit from them.
you think n1's worth the money
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top