Welcome to the SR20 Community Forum - The Dash.
Register
SR20 forum logo

Thread: What Did You Do To Your B14 Today?

+ Reply To Thread
Posts: 1,691-1,700 of 2,656
2011-12-08 00:51:41
#1691
^ All you do is make screw holes and screw it in to the console after you measure how it will fit. Simple, just never take it otu or u will have holes.



Today i went to get a haircut, got in the 200sx and just started it and hear a car alarm from a smart car go off behind me lol. Guy runs out looking at his car (dude i dont think anyone is going to take a fucking smart car) and goes back into the at&t store, i back up and barley hit the throttle and the alarm goes off again lol.
2011-12-08 01:14:57
#1692
Originally Posted by danfiveten
^ All you do is make screw holes and screw it in to the console after you measure how it will fit. Simple, just never take it otu or u will have holes.



Today i went to get a haircut, got in the 200sx and just started it and hear a car alarm from a smart car go off behind me lol. Guy runs out looking at his car (dude i dont think anyone is going to take a fucking smart car) and goes back into the at&t store, i back up and barley hit the throttle and the alarm goes off again lol.


What mods do u have to the exhaust? Full catback, header n no res or what lol
2011-12-08 01:32:11
#1693
Originally Posted by nismosigma
how does this mouunt ive been thinking of doing it for a while now


Simple stuff, like danfiveten said, I used the same bolts that came with the armrest, just need to measure it good to get it in the center of the console. Note, the Altima and '99-02 G20 armrests look like they could fit but they are too big. The '91-96 G20 armrest is the one u need to look for.

2011-12-08 01:54:30
#1694
I used to have the g20 armrest untill someone finally put a nice 200sx one up for sale.


I have a mandrel bent 2.5 inch exhaust with magnaflow. I have no resonator, Its not that loud, and its not ricer sounding, it sounds alot like my 71 510, and i set alarms off with that thing (which i secretly love) and i can usually make my exhaust sound quiet when driving by feathering it, but apparently his alarm was very sensitive. I love it.
2011-12-08 05:28:25
#1695
installed a front ST Sway Bar a few hours ago. I haven't got a chance to test it out but I noticed as soon as I sat in it to move it it was very stiff. I could rock the front end side to side like it was pivoting on the center.
a comparison shot

installed

and a b13 rear bar for sale, no hardware just what u c in the pic
2011-12-08 09:42:43
#1696
Originally Posted by kid200sx
installed


This doesn't look right, you have the sway bar below the control arm. It should be installed above the control arm with a bushing on each side of the control arm.
2011-12-08 18:23:47
#1697
Originally Posted by sr20jet
This doesn't look right, you have the sway bar below the control arm. It should be installed above the control arm with a bushing on each side of the control arm.


Thats what I thought before searching installation pics. All the pics I have found are mounted this way.
ST Sway Bar Install Notes
"The install was pretty straightforward, as the mounting points are the same as the stock bar. The only thing different is that the new bar attaches below the transverse link/control arm, while the stock attaches above it. Because of this the ST bar is straighter; with less curves in it."
2011-12-11 08:11:14
#1698
Had a ricer try to do a ricer fly by twice =\ ended up racing him for real (out on a private road) and pulled on him so damn hard its not even funny lol... Was a lowered red civic with a sticker on the side window saying "Team (something I couldn't read)" rofl
2011-12-12 12:50:37
#1699
Drove like a drunk guy to class. Damn potholes!
2011-12-13 03:41:50
#1700
Fell in love with her all over again in only a 5 mile drive after driving my moms benz ml 350 for 3 days. Don't get me wrong, its a nice car but there is no feeling to the drive... I love my car and I don't care what anyone says about her.
+ Reply To Thread
  • [Type to search users.]
  • Quick Reply
    Thread Information
    There are currently ? users browsing this thread. (? members & ? guests)
    StubUserName

    Back to top